Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

jroberts197111

1986 Suzuki lt250r need crank

Recommended Posts



That is a good question, the crank bearings are the same, so it is likely that it will fit in the case. But the piston and cylinders are differen, so, you may need to swap those too. I would ask find someone who specializes in working on these machines, maybe someone on a forum dedicated to the LT-250R, and ask them. I think a dealer tech will just look at the different part numbers and tell you it won't work. You need to find an old Quadracer guru, like Dr. Q. I hate to send you to another site, but I don't know that there is anyone here that can tell you, so check this link out. QuadracerHQ

Share this post


Link to post
Share on other sites

DD is right I have an 87 and I know that the 87 is a different beast from the rest. I agree QuadracerHQ is an excellent place for answers about the Quadracers.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Reece Bowen
      x   just bought this expedition 425 and the Speedo needle does not work. The lights work for the shift indcator. So is this an electronic Speedo or cable? Is there a way to fix it or will I have to replace the unit? Thanks for any help you can provide.
    • By Mike Johnson
      Hello again guys ,. I have a Quadmaster that has a very bad lean to my passenger side wheel. I replaced the a arm bushings with no change in the lean,  I see no bent parts and no adjustments available. It's always been there since I got it but became really noticeable when I put the lift kit on it. I'm going to add a picture of the problem if allowed.

    • By Kaj Colum
      Pushing the start button the engine turns and will forever without starting. But if I use the kick start it will start with one or two kicks everytime, any idea as to what is going on. New good battery and coil, I'm ready to try anything. It's a great bike, but this is getting anoying. Thank you.
    • By Mark Hill
      Hi everyone bought my son a project wheeler and got it up and running but it won’t go in reverse.  It’s a 2002 2003 bombardier rally 200. I have been searching for causes on line had have a couple ideas what it may be but still looking  for advice and help
    • By Sharon van den Berg
      We bought an old atv from friends to bum around on the farm with. VIN number is rusted off. Is there a way to determine the year model from the engine number? We only need the info to buy parts. Please help


  • Similar Tagged Content

    • By Anthony Marceau
      Hi everyone! I have a 1986 yamaha moto4 200 that's been sitting for a while! Cleaned the carb, replaced engine oil, put fresh gas in it. Got it running and went for a ride! It was running great just a little backfire once in a while! I barely made it home on the way back and now the bike won't run at all since then! It will start if I give a little bit of throttle but dies instantly as soon as I let go off the throttle! And even if I try to rev it up it'll sound like its not getting enough gas.. it revs up a couple hundred rpm's and backfires through the carb.. it almost sounds as if I was trying to take off from zero in 5th gear! Nothing is seized though! I dissasembled the head and the piston and cylinder are fine! Rebuilt the carb, replaced the ignition source coil.. I don't know what to do anymore.. compression test shows 90 psi Specs are 128 psi but i'm not sure if I trust my compression tester.. any ideas? Thanks!!
    • By sloundez
      Does anyone out there know where I can get a functional pair of wheel cylinders for subject ATV? Any suggestions welcomed. Thanks
    • By chuckcnm
      Hi, just picked up a MOTO 4 YFM255 and want to replace the rear brake pads. How do I get to the back. Guessing I need to remove the brake disk, question any easy way to do this?
      Thanks
    • By Jers
      I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
    • By Steve1266
      I went out to ride my quad today. When I started it up it ran for a minute, then died. Since then it will turn over but won't start. I've check the spark plug and get great fire. I have had this quad for about 6 months, and very new to breaking it down. But need help. Thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...