Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

waynemags

1995 Yamaha Big Bear Rough Idle

Recommended Posts

hey guys. new hear. i just got a 95 big bear that ran fine when i looked at it, but now when i startit, it idles real bad. it runs for a bit at a higher idle, then dies right down and then dies. fire it back up and turn the idle screw in and it idles high. will run fine for a bit then stutters and idles down almost dies then lights up again, then a second later, dies. ive cleaned the carb the best i can . blew out the passages and tried again. still does the same . the air screw was bottomed right down. i opened it to about 2 turns out. seemed to bring the idle back up, then stuters and back down till almost dead, then dies. any suggestions?

Share this post


Link to post
Share on other sites


Welcome aboard! Did you take the carb out and clean it? Did you inspect the float and pin?

* Adjusted your thread title to include issue and manuacturer.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By JacobSlabach
      Hey I have a 97 bayou 300 2x4 (klf300b) that i bought for 1000 last June and sunk another 1000 into it already.  When i went to look at it, the seller had warmed it up before hand (he was riding it when I got there).  it ran good so i bought it and took it home that evening... next morning it wouldn't hardly start.  I discovered the carb was clogged, there was chunks of rust in the fuel valve, the choke lever was missing and other things.  I have since cleaned the carb and replaced the fuel valve and gas lines and cleaned out the gas tank and cap.  
      Enough background on it, the problem is this:  It floods if i push it past half throttle in 4th and 5th gear even going downhill and shifting correctly.  It also has to idle and warm up when you first start it which is really annoying now that its cold...  It also smokes blue smoke for about 15 seconds when started cold-  does not smoke at all once warm but the exhaust still smells like burnt metal.  A friend told me that it didn't have enough compression.  I also found out that the valves are a common cause for low compression on Kawasakis..  I have never adjusted valves before-  the most I've ever got into a engine was a head gasket on a riding mower so I'm new to this.  My goal is to get this bike running and starting cold like a top-  should i tear down and rebuild the top end?  What should i try first?  I tore the carb apart and rebuilt it and fiddled with the air screw and nothing changed.  I also ordered a compression test kit that should be coming in soon.

      Ive also considered just selling it for like $500 and taking the hit-  Id rather not sink too much more into this machine..  lol
    • By JacobSlabach
      recently picked up some project bikes off CL for cheap.  got a honda fourtrax (the ancient 4x4 kind with the straight axle in the front as well as the rear and a back-up kick-start)  plastics are crap, but my goal is to get running like a champ and patch the plastics up and sell to one of my many friends that want a reliable 4x4 for dirt cheap and doesnt care what it looks like.
      so the former owner says it needs carb rebuilt, but its sat for 3+ years since so who knows.  things I see:  carb is missing (he gave me a box of parts along with the bike), engine turns over and feels good with kick-start, brakes need work, battery missing (That always puts me off, cause then I know most likely someone's been tampering with the electrical.
    • By ray desocio
      I posted earlier looking for a wiring diagram, but maybe someone can help me with the problem if they’ve had it before. 
       
      The quad Will start and idle ok, when I open the throttle it will rev all the way up until WOT and then it dies back down to idle, and if I keep the throttle wide open it will rev back up. It will do this over and over and over. 
       
      I replaced the carb, (twice), Rectifier, battery, and spark plug.  The Stator ohmed out to the proper specs from dinli.  The other issue i can see is I’m not getting 12v on the choke circuit. The lights don’t work either. 
       
      possible bad key switch? Maybe the new rectifier is bad? All the contacts on the key switch also ohm out properly    
      comprsssion is up to 125 psi and spark is there. 
       
      Reed valves look great.....
       
      im at a loss. Any trouble shooting advice would be appreciated. 
    • By Colin Davis
      I recently acquired a Yamaha bear tracker 250 that does have a wiring harness.  Does anybody have a wiring diagram for the 250s. Also if you have a pin diagram that tells be the colors of the wires going to the cdi and rectifier or just a picture of the plugs would be much appreciated. I can’t find anything on the harness online. I have all of the switches and stuff and I plan on just build a harness myself because I can’t find one to buy.



  • Similar Tagged Content

    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By alexcross324
      Hi all, I try to find this manual in the threads but you have a lot of stock here
      Cannot find this particular manual.
      I found it for YFM200 but not sure if they are the same.
      Thanks if you could help me with that.
      Im new here so if I did something wrong, please tell me.
    • By davidwestfall
      looking for direct shift shifting lever that properly fits my 2003 Yamaha warrior 350 and fits my foot the same as a stock 2003 Yamaha warrior 350 shifting lever fits my foot
    • By davidwestfall
      hey I'm dave westfall I'm new I just became an official member of this site a few minutes ago. Ive been crazy about quads and bikes since I was about 3 and ive always done my home work on them figuratively speaking. I would say for comparison to the common man that I am pretty knowledgeable about them. its been my passion about most of my life. I love talking about quads and bikes so if anyone out there would like to talk with me about mechanical subjects or about person experiences while riding or just shoot the breeze please feel free to chat with me. I'm looking forward to it.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...