Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

nybronc

wolverine 4 wheel disconect by warn

Recommended Posts

i found out warn stoped making the 4 wheel drive to part time 4 wheel kit for the wolverine ,any idea's where else the kit might be available ?, thanks, nybronc

Share this post


Link to post
Share on other sites


I did check ebay, I found 1 for sale for 400.00 buy it now price, I'm thinking about it because I found a wolverine I want to buy but I don't want full time 4 wheel, I found a mint one with low hours but the cost of the atv and the warn unit at 400.00 I might be better off looking for a differant model, I have a warrior now that I like which is why I want a wolverine, I could buy a newer one but not sure if I want a automatic, it takes some of the fun out of it. Todd S.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Scott Sirr
      I need to figure out how to clean/fix or replace my neutral switch assembly On my 2008 Yamaha big bear 400 as generally the neutral light doesn’t come on when it is in neutral. To get it to come on I have to wiggle the foot shifter and hold it in just the right spot.
      I have googled it and can’t find much on the 400’s. I can’t find a service manual online and the parts manual is super vague.
      I think it is in the right side engine cover area, but not certain. 
       Any help would be great. thanks
      Scott
    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By YamahaGrizzly
      So my Yamaha grizzly 700 wasn't going into reverse for some reason but Jon and George figured it out on what to do to fix that problem for me. Jon Talks about how he was able to fix that problem my Yamaha Grizzly was having with the reverse.
      On a side note we are so close to 1k subs! hell ya!
    • By StolenATV
      went to sell this guy my bike and on his test drive he just took off and never came back.
      The post 2015 Yamaha YFZ450R Stolen During Test Drive appeared first on STOLEN 911.
      View the full article
    • By Tracy Flickinger Vargo
      Hi.  New to all of this.   13 year old Son bought a 2013 TaoTao ata -150c quad that needs a new harness and stater.  Tao Tao said they discontinued the model and making replacement parts.  Help?!?   Anyone know where to find these parts?   
  • Similar Tagged Content

    • By Ironfist104
      My wolverine has a new carb kit, new battery cranks over and over take it to the point of killing the battery to start sometime.... but it I give a tug on the start rope while I'm cranking it with the starter it fires right up.... any advice?
    • By dblbassdrumer
      [ame]
      [/ame] only when u pull back in the clutch does it make this noise and wanna take off
    • By oldcomet
      Morning Folks
      Ok so I have taken the front hubs apart everything is good and working fluids changed and full In 2 wheel drive the bike works great However in 4 wheel drive high I get a grinding clunking noise right near the foot pegs The universals are all brand new in the complete bike The problem just started after my last ride Sometimes I have to change the rpm to get the bike to go into gear in forward and reverse The bike doesn't make the grinding noise when I have the bike in 4 wheel driver low gear only in high gear Could the shifter need adjusting any help would be great Thanks for your time
      Oldcomet
    • By Quadguy420
      I have a 2002 prairie 650 and when i have the handlebars as straight as i can get them the one wheel toes out and isn't straight . is there anyway i can adjust this ? or anyway to rectify it .
    • By dwo0100
      Just bought this machine and really need a service manual. Had the rear end go out after owning it one afternoon. Thanks for your help guys.
      1997 Yamaha Wolverine 350 4x4
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...