Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

snugglebunnie74

2005 Yamaha Bruin 350 Remove Timing Chain

Recommended Posts



Adjusted your thread title and included year, make, and model. Also removed your other duplicate thread. Welcome to QUADCRAZY!

Share this post


Link to post
Share on other sites

Proabably too little, too late, but, the first thing you need to do is remove the valve cover. This will likely involve removing the tank as well. Next, on the upper, rear facing surface of the cylinder there will be a small fitting with smaller screws at the top and bottom, in the middle, there will be a slightly larger one. This is the actuall timing chain adjustment screw. Back that off untill there is some slack in the chain at the top by the cam. If the chain does not loosen up by backing that screw out, then start loosening the screws above and below that hold the fitting itself on. Once you have the tension off of the chain, you can unbolt the camshaft sprocket from the cam. Make sure to mark the chain and sprockets with something that won't smear off. If there are marks on the chain and sprockets, then it won't be necessary to mark them yourself. Then you will need to remove the left hand side cover, remove the flyweel and stator, and at that point you should be able to work the chain around the output shaft of the crankshaft. I am sure there are alot of other little things I did not mention. If you have a good mechanical inclination, you should be able to figure it out. If you aren't so good with a wrench, I would atleast buy a repair manual to help guide you throught he steps.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Dwight Williams
      Ok, so I bought a 2006 bayou 250 for 200 bucks, kid couldn't start it and had no idea why it wouldn't run, I pulled the rope and felt what I thought was valve to piston contact, he wanted 500 and I talked him down to 200 and brought it home.  Sure enough, timing was way far out, timing chain incredibly loose.  So for fun I re-tensioned the timing chain and re timed it, got about 120lbs of compression, pretty low.  I cannot get the chain very tight but the the tensioner seems to work fine, the chain guides don't look very worn.  Also, when I took the head off the valves don't look bent and the piston has no discernible marks on it.  Is this an interference engine?  I sure thought I felt some contact with the pull rope but maybe no permanent damage was done?  Anyway, I plan on doing a full top end job as well as timing chain tensioners and hopefully that'll cure it.  Is there any reason other than chain stretch (I measured it and it's ok) or guide wear that would cause the chain to be so loose?  Thanks!
       
    • By BosoxBruce
      Recently I noticed gas leaking from under the gas tank on my 2005 250 2x4. As I looked closer it appears to be leaking from the shut off valve under the tank. It's the valve with the handle that can be turned to open, close or reserve. Can this part be replaced? Thank you.
    • By Michael Aiken
      Where can I find a wiring diagram for my 2005 450 Kodiak. Thanks.
    • By DUBLT
      Looking to purchase a windshield for my ATV, suggestions of what to buy with quality in mind and will fit without doing any modifications. 
    • By Barry Troxtell
      I have a 2005 Sportsman 500, Instrument cluster will not illuminate, hi/lo beams work though.  Any tips or troubleshooting info is greatly appreciated!
  • Similar Tagged Content

    • By Michael Aiken
      Where can I find a wiring diagram for my 2005 450 Kodiak. Thanks.
    • By Mo Salem
      So my front hub broke, I’d like to put aftermarket on. Hard to find new oe ones. Please help. I’m new to all of this, I have some car knowledge and try to apply it
    • By oxidized_black
      tag : zukifreak
       
       
       
    • By LMI
      Was using the quad the other day to shuttle wood from my pickup to my wood pile.  When the job was done I turned off the Quad and heard a bit of a racket from the front end.  When I got down underneath the sound seemed to be coming from the fan housing.  fan was moving in spurts and not quickly... much like a computer case fan that's had it's day.  What I know.
      Temp sensor is ok, as the fan tries to activate fan is getting some voltage as it is attempting to spin.  When I first bought it used I tested the fan direct to battery and it was fine. The fan was working ok even not direct wired as I went on a couple of rides and when stopped and idling the fan did run Seems to be free spinning with my finger read up in the manual and they require me to drop the rad.  now I'm not opposed to that as the rad has some damaged areas I want to try and straighten out.  But if I can get the fan working without, I can leave the rad as it is until next year.
      Fan assembly is about 300 bills, any work arounds or alternatives?  I even thought large computer case brushless fan.  smaller ones are about $7 larger ones better quality probably far below the 300.  They run standard 12v DC.
      Anything I should be doing before dropping the rad... other than check for obstructions even though it seems to spin, and trying to hardwire it to the battery again for a test to see if it acts the same?
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...