Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

casper_sr_00

2001 Polaris Scrambler 500 4x4

Recommended Posts

i have a scrambler 500 4x4 its a 2001 for some reason all the lights,fan and the four wheel drive stopped working im not sure if there are any fuses on it but i cant seem to find them anywhere all the wires look good that i can see not sure what to do. Anyone with this problem? does anyone know if this four wheeler has any fuse if so please let me know [email protected] thats my email thanks Chris

Share this post


Link to post
Share on other sites


I am pretty sure they have inline fuses on them, you might be able to find a manual on ebay. or a wiring diagram to make sure.

Share this post


Link to post
Share on other sites

If you have a multi-meter, get it out and start checking for lost power. Start at the battery and trace each circuit back toward the problem area and see where you lose power. Chances are that a primary circuit, responsible for powering all off the things you are having problems with has failed. Could be a fuse, could be a shorted wire, could be a loose or corroded connection or ground. If you don't have a manual, get one, they are a must have IMO.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By cfauvel
      So I've had my bro-in-law's 4 wheeler to get it running again. 
      Ended up buying a new aftermarket carb, cleaning fuel tank, cleaning petcock and it works near perfectly .
      put the petcock to PRI for about 5 seconds , turn it back to on, pull full enrichener , start it  up (starts right up), slowly release the enrichener and put it in gear and go up down the road. Slow, fast, idle etc all good

      BUT then out of the blue it will start missing badly (by this time the motor is hot), to the point I can't move the ATV.
      Then out of the blue, maybe 30 seconds later, it is back to normal and I can go up and down the road for testing just fine.

      I'm trying to get the ATV in tiptop shape to return to him, but bugged by this miss, I'm sure this machine will come back to me if it keeps missing...

      Thanks in advance
       
      BTW I am mechanically inclined, but not an expert on this atv...
    • By 2urb0liter
      Looking for front wheel assembly (hub, axle, rim, tire) for 1982 Honda ATC 110. 
      Let me know what you have and how much shipped to 58504. 
       
      Thanks!
    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By Arizona
      Trying to figure motor size, says nothing on plastics, or the title, only numbers are EC25PFX 01 Which
      are on the cylinder. The vin code is 4XAAG25C312459874
      Tried vin search but still doesn't show motor size. 
  • Similar Tagged Content

    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
    • By RoxanneRoseReid
      Need a polaris manual for a 1994 2 stroke 2/4x4 quad free. can you please post a link I can click on Thank you. Roxanne
    • By buzzar56
      I am looking for a free repair manual for a 2003 Polaris sportsman 500 ho atv. all the posts on here lead me noplace
      thanks fred.
    • By Weldingrod47
      Trying to change front wheel bearings. I removed the cotter pin and castle nut. Hub won't budge. Is there an additional retaining clip? Seems to be one of those push on type that barbs on the thread of the spindle. How do I remove it?
    • By warkcol
      I am having an issue where it sounds like the gears are slipping if I hit the throttle really hard and also after letting off when the engine brake is applied. Also, the drive train that goes to the front also rides again the gear shift box. I will attach pictures and a video here shortly.
      Thanks in advance!
      [ame]
      [/ame]https://postimg.org/image/cdlu6fza9/
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...