Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

roosterqt

2008 king quad 450axi clutch problems auto

Recommended Posts

Hello people, my king quad has been jumping in to neutral while at slow speed engine braking if i blip the throttle it re-engages, my dealer cant see any problem when he opened it up, does anybody come across this, is there a sensor for the engine braking system, thanx....

Share this post


Link to post
Share on other sites


Welcome to QUADCRAZY! Are you saying that the lever jumps into neutral, or it just starts slipping?

Share this post


Link to post
Share on other sites

I am just shooting in the dark here, but it seems like there is something wrong with the clutch shoe or maybe a loose belt is letting the tension off of the clutch causing it to disengage. Good luck.

Share this post


Link to post
Share on other sites


i have a portuguese suzuki dealer and my portuguese is minimal, as is portuguese communication,but after 5 weeks of phone calls and little reply a new suzuki clutch is on its way,but thanks for the reply dirtdemon the belt sounds more likely due to the none slip when the throttle is on, only when gentle engine braking it gets worse ,,what does the clutch shoe do?

Share this post


Link to post
Share on other sites

It is the internal part of the centrifugal clutch mechanism. In your case, shoe is mechanism with moving parts (themselves referred to as shoes in most centrifugal clutches) , that swing out when rpm's reach a certain point and engage the clutch.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By David Miller
      Does anyone know how to access the check engine codes on a 2018 450 sportsman. Just changed battery and spark plug . It runs fine but the light is on and I need this to plow snow and need it reliable. Any ideas . Thanks
    • By Ajmboy
      Interesting to read what the thought process was only 63 years ago. Might be BS according to some of the posts on reddit. This was actually posted 15 years ago and making its rounds again...lol.
       
    • By Venom
      Hi All,
      I did a total restoration on a 2003 Yamaha Raptor 80. Rebuilt the engine and tranny.. Started it up today and it runs great. Took it for a ride and the transmission worked perfectly. Adjusted the carb a little more and went for another ride. It ran awesome, pulled into the workshop shifted into neutral ( Neutral light came on) and shut off the bike. went to roll it and noticed she would not roll. Turned on the key and neutral light was on... After some troubleshooting I found that she is in first gear with the neutral light on and will not shift into neutral... It seems to up shift fine into 2nd and 3rd and then back down to 1st. I am hoping somebody can shed some light on what is happening... Thanks for any help...

    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By Skhot K
      Hello! I picked up a YFM400 and I would love to talk shop with knowledgeable co-owners, and I'd love input about the machine from anyone here who clearly knows more than I do! Cheers from NY
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...