Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

ozzie

2008 Yamaha Big Bear 400 - Engine cuts out low idle

Recommended Posts

08 Big Bear 400 - Engine cuts out at idle and low RPM. Sounds and feels like you turn off the key and then right back on. Sometimes it will die when idling. It does this sitting still or moving so I do not suspect wiring. Runs great at higher RPM no cut out or missing. The machine starts very easily at all times hot or cold. I have checked or replaced the following; air cleaner element, spark plug, plug wires and ignition wiring, fuel filter, carb bolts and gasket. There are no unusual engine sounds. Bike has about 600 miles. I push snow with it and it is very annoying as many times I operate at a low rpm and that is when this occurs. Any ideas would be greatly appreciated. Thanks

Share this post


Link to post
Share on other sites


Is there an idle adjustment on that? Have you checked your choke operation?

* Edited your thread title to include year, make, model. and issue.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Dave Ayoub
      Ok i am not quick to jump on a forum and post a question without doing my own part and trying to research and solve the problem myself but I cannot find any definitive information anywhere about my problem. I have a Big Bear 350 that I picked up very cheap which had been sitting in a field for years. I am not new to building wheelers but this one has me beat. After rebuilding top end and replacing the carb it fires right up. The vin has some number worn off from being next to the shifter but from the parts in the clutch i assume it is early since 87 parts seem to be the only ones that match. Thats when the plot thickened. 
      Reverse works fine but when in the forward gears it would not go past 1st and was hard to get into neutral. ie. a it took a million clicks up to thump into 1 and as many down to find neutral. still never getting past 1st. within minutes i could hear metal screeching and whirling around in the clutch side of the motor. I took the cover off to find that 3 out of the 4 springs on the centrifugal clutch had broken and were shredded. Also the black mechanism that the pawl on shift shaft grabs moves was loose so it wasnt always grab to change the gear on the transmission. I tightened that mech, and replaced the springs assuming it would solve the problem since the gears were not actually changing from the lever and the carrier should obviously not only have 1 spring left. 
      After putting everything back together it did go into 1st fairly easy but then i again couldnt get it back to N without a million clicks down and couldnt get it to go past 1st. I did one time get it into a higher gear who knows what one but i gained some speed and dropped rpm.
      If i jack both the front and the back wheels off the ground and run the motor it becomes much easier to shift and i can get it to run through the gears pretty well. Usually going into N without a huge fight. not perfect but it does hit neutral and roar while spinning the wheels instead of gain rpm and with the power. 
      I have tried every possible position on the clutch adjustment screw without any noticeable result. I think this could potentially be where my problem lies at this point.
      does anyone know if the case is supposed to be threaded? because mine is not. obviously it seems as though it should be since every other bike ive touched has been. i even took the cover off my quadrunner to make sure it wasnt crazy.
      when the screw is adjusted and the jam nut tightened the screw will just slide back out since there is no threading in the case. accomplishing nothing. 
       
      Does anyone have any insight on any of this? Are my plates stuck, Centrif clutch worn out, case stripped or something else crazy im over looking? 
       


    • By dbconn55
      Hi guys I have a 2003 Arctic 250 4X4 it starts idles and runs great for about 10 min. then it spits and sputters and dies but it starts right up like nothing happened idles good till you give gas and it does it again let off the gas and it's idling great again this goes on for about 15 to 20 min. and then it takes off runs good all day like nothing was wrong.
      I cleaned the carburetor it looked like a new one inside found a little gunk in one orifice, new air filter no crimped lines air line to tank good I did put a meter on the battery idling it said 16.5 V that's high I think would a voltage regulator cause this?
      Suzuki shop wanted to sale me a stator for $556.00 but said it could be something else also thought I'd see what you guys say about it
      Thanks
    • By MarkinAR
      So this 98 Big Bear is my new project.  While I'm waiting on a few parts to show up, I'm working on a few small things.  I can shift 1-5 just fine, no problem at all (keep in mind, this is not running yet so just manual shifting sitting still).  However, I can't shift from 1-neutral.  I can hold down on the foot shifter, rock it a bit, and it will disengage the clutch so i can push it around in neutral as long as I keep pushing down on the shifter.  However, it will not downshift to neutral and stay there.  I know BB's have had some shifting difficulties in the past, but before I dive into this, have any of you fine folks encountered the same issue?  I'm tempted to just adjust the linkage a bit since these have an external linkage, but thought I'd toss the question to the group and see if there are any common issues to look for.
      Thanks guys...
    • By Ryann Racho
      So Id say about 2 years back I bought a 2013 Polaris Sportsman 500 H.O. off of my uncle. It ran perfectly, nothing wrong at all. I usually go mudding with it or just ride trails with buddies. So as you would assume, the quad is quite dirty from sitting for a few weeks.
       
      STUTTERING PROBLEM: I noticed one day out of nowhere that in high gear at 15-20 MPH, I was already maxed out at 4500-5000 RPM  It would get to 15-20 mph, max out on rpms and start sputtering. It sounded like it was basically acting like it couldn’t go any faster than this.
       
      IDLING PROBLEM: I was fucking with the carberator the other day maybe thinking that is causing my sputtering, and now my idle will shoot up to 2600 on start usually, then I will turn the throttle adjustment down to the normal 1400. The rpms with then fluctuate 10-30 rpms back and forth repeatedly, it will then run for about another 30-60 seconds and the RPMs will slowly drop to about 900-1000 RPM and stall out. I replaced the carburetor and everything seems to be working perfect on that, no leaks and what not but it’s still acting strange. Also, I’ve noticed that when looking into the Electronic Throttle Control that two plates that aren’t supposed to touch have to be WAY past touching to even try to fire up. Even when set at a wide open throttle like that, I still have to give it some throttle to get it to fire up.
       
      Here is what I have done so far: 
      Checked the belt and clutch
      Changed out spark plug (Last one was covered in carbon)
      Cleaned the intake and air box
      Replaced the carburetor
      Replaced the inline fuel filter
      Checked that all lines on carburetor are connected into the right spots
      Checked If intake boot was cracked (Not from what I can see)
      Unhooked and reattached new carburetor (About 4-5 times)
      Cleaned battery terminals and battery off
      Shut on and off Gas Line Cutoff Valve
       
       
       
      My next thoughts are that maybe the TPS is fucked up or maybe the Spark Arrestor is plugged with mud. I was thinking tomorrow to purge the exhaust and also check the ohms output on the TPS.
       
      ANY HELP IS GREATLY APPRECIATED. I HAVE BEEN BATTLING THIS FOR WEEK AND REALLY WANT TO GO RIDING. THANK YOU!
    • By Larry Fox
      Looking for the wiring diagram of the gauge cluster. Thinking about using it on my 2008 that I just bought.. Its gauge is destroyed
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...