Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

sprad22

2002 arctic cat 500 auto won't go forward or reverse

Recommended Posts

Hi I have a 2002 arctic cat 500 auto.starts and runs but will not go forward or reverse.the outer clutches/pulleys and belt spins but it will not move when put in gear.Any ideas as to what to to check for?clutckes,broken gear????

thanks for any ideas..

Share this post


Link to post
Share on other sites


I would go with a clutch problem. It is very unlikely that it is broken gears. clutches are the weakest point on any clutch applied system.

Your friendly neighbourhood Journeyman mechanic :)

Share this post


Link to post
Share on other sites

Agreed, if the belt sheaves are grabbing and moving the belt properly, then the next possible problem is definately the drive clutch. I would tear down to the clutch and check the clutch shoe and the small one way clutch that is between the clutch housing and clutch shoe. Make sure all moving parts are moving freely and check for excessive wear on any clutch components. One question, have you tried putting the machine into 4wd and seeing of the front drive system will move the quad?

Share this post


Link to post
Share on other sites

Ok,Thanks for the replies.It will not move in fwd or 2wd.Will tear down and check the clutch this weekend.Thanks again.

Share this post


Link to post
Share on other sites


I was driving my four wheeler and it just stopped going in the middle of the road it just sits there running but when I go to move forward it just makes like a chugging sound and stays put I changed the spark plug and cleaned the carb..... What eles should I do.....  

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Amboyjim
      Having serious problems with quad it completely stopped running on me took carb off and tore apart cleaned everything put back on and it started idled but when driving it had no power at all so took carb back off and noticed their was a puddle of gas and oil in the bottom of the air filter box and also their was gas in the vacuum line HELP
    • By JacobSlabach
      Hey I have a 97 bayou 300 2x4 (klf300b) that i bought for 1000 last June and sunk another 1000 into it already.  When i went to look at it, the seller had warmed it up before hand (he was riding it when I got there).  it ran good so i bought it and took it home that evening... next morning it wouldn't hardly start.  I discovered the carb was clogged, there was chunks of rust in the fuel valve, the choke lever was missing and other things.  I have since cleaned the carb and replaced the fuel valve and gas lines and cleaned out the gas tank and cap.  
      Enough background on it, the problem is this:  It floods if i push it past half throttle in 4th and 5th gear even going downhill and shifting correctly.  It also has to idle and warm up when you first start it which is really annoying now that its cold...  It also smokes blue smoke for about 15 seconds when started cold-  does not smoke at all once warm but the exhaust still smells like burnt metal.  A friend told me that it didn't have enough compression.  I also found out that the valves are a common cause for low compression on Kawasakis..  I have never adjusted valves before-  the most I've ever got into a engine was a head gasket on a riding mower so I'm new to this.  My goal is to get this bike running and starting cold like a top-  should i tear down and rebuild the top end?  What should i try first?  I tore the carb apart and rebuilt it and fiddled with the air screw and nothing changed.  I also ordered a compression test kit that should be coming in soon.

      Ive also considered just selling it for like $500 and taking the hit-  Id rather not sink too much more into this machine..  lol
    • By Colin Davis
      I recently acquired a Yamaha bear tracker 250 that does have a wiring harness.  Does anybody have a wiring diagram for the 250s. Also if you have a pin diagram that tells be the colors of the wires going to the cdi and rectifier or just a picture of the plugs would be much appreciated. I can’t find anything on the harness online. I have all of the switches and stuff and I plan on just build a harness myself because I can’t find one to buy.



    • By quadtech62
      I have a 02 Warrior i am trying to build a wiring harness i have looked in the manual and  i am confused... the pick up has 2 wires.  W/R W/G The source rotation coil has 2 wires. One is Red other is white/blue. The manual shows the  the white and blue wire connected to the w/g  right after the stator... so why is these 2 wires connected?  Does not show w/b wire at cdi 
      i have looked at many options with no luck if someone has a 2002-2004 warrior and can take a pic of the wires and location at cdi i would really appreciate it. Thanks
  • Similar Tagged Content

    • By Jean de la Chevrotière
      View File Polaris 700 2002 Owner's manual
      Polaris 2002 700 Owner's Safety and maintenance manual
      Submitter Jean de la Chevrotière Submitted 12/01/2018 Category Polaris ATV  
    • By Jean de la Chevrotière
      Polaris 2002 700 Owner's Safety and maintenance manual
    • By priglmeier
      I own a 2002 Can-Am Quest 650.
      It will start if you massage the throttle a bit and it will continue to run. BUT if you let go of the throttle and try to let it idle it will always die warm or cold.
      It has Non-Oxy premium gas, a new gapped NGK plug, a new carb (as of today) and fresh fluids. After installing the new carb it runs exactly the same.
       
      I only have a few things that I have observed since the new carb:
      The choke still doesn't do anything. It has a good cable and it is hooked up. It on fully off. There is a cable in the top, front of the engine that splits into two connectors. The connected side is in the photo. The other side has the yellow banded section and is not connected. I do not see anything in range of this connector so I don't know if this is normal or not??? The original carb wasn't really dirty or clogged. I'll use it as a spare. I don't see this cable and connectors listed in the Can-Am shop manual. Looking for some help. I want to ride!


    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...