Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

daniels217

2007 Honda TRX 420 ES transmission problems

Recommended Posts

will not shift with the emergency shift wrench . it is giving me dtc code 2long 2short need help . i have a shop manuel for this atv and can't figure it out.

Share this post


Link to post
Share on other sites


I take it that the electric shift doesn't work either, does it do anything? Do you hear a noise or anything that indicates that the shift servo is trying to work? Doesn't the shop manual tell you how to read the codes? By shop manual, do you mean the owners manual or do you have an actual repair manual? You need a repair manual, the owners manual isn't good for much more than telling you what kind of oil to put in it. I have no idea what the flash codes mean, but if the machine won't even shift manually, I would guess that either your clutch is faulty, out of adjustment, or you have bent shift forks or some other damage to the gearshift mechanism. I would start at the clutch since it is easier to get to and it can be adjusted from what I understand. The shop manual should tell you how to do it. If that doesn't help you could remove the side cover and inspect the shift ratchet. If it is a bent shift fork, or shift drum problem, you would have to get inside the motor.

Share this post


Link to post
Share on other sites

It's more than likely a thing called the ' shift angle sensor' I have replaced HUNDREDS of them over the years. Dealer part, not too expensive... screws into the back of the case above the swingarm. betcha a quarter that's it!:yes:

Share this post


Link to post
Share on other sites

Would a sensor keep him from being able to shift the machine manually with the emergency wrench? Seems like the sensor would only affect the electric shift.

Share this post


Link to post
Share on other sites


yes, actually it can, if the sensor fails during an electric shift. It jams the shift forks and shuts off the actuator motor. annoying as heck! I've seen it many times... recons too.

Share this post


Link to post
Share on other sites

I see, that makes perfect sense. I have heard of people having chronic problems with these electric shift systems. Ironically, a friend of mine has an '04 Rancher 350 ES, and it has been horribly mistreated, however, the electric shift is the one thing that has always worked.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Aaron Ruiz
      Hey I'm new to the Forum but I just wanted to talk about my Scrambler I just picked up and when I first picked it up I thought it was okay but after I got home and everything I noticed it's very hard to shift into drive neutral reverse it is possible to shift into those gears but it's very stiff like and it takes a lot for it to actually engage to move forward. In Drive when I press on the gas it takes a while for it to actually start moving in the RPMs go up before it starts moving I inspected the belt it looks fine to me I checked the transmission fluid and it was low so I put some. I just hope transmission is not out just curious if you guys have any ideas
    • By Kevin Vlogs
      Hey Guys,
      I'm pretty new to ATV's and never owned a Polaris before. Lately I have noticed that it is very hard to shift from Park to any other gear. Is there an adjustment, or is that just the way they are?
    • By Dave Ayoub
      Ok i am not quick to jump on a forum and post a question without doing my own part and trying to research and solve the problem myself but I cannot find any definitive information anywhere about my problem. I have a Big Bear 350 that I picked up very cheap which had been sitting in a field for years. I am not new to building wheelers but this one has me beat. After rebuilding top end and replacing the carb it fires right up. The vin has some number worn off from being next to the shifter but from the parts in the clutch i assume it is early since 87 parts seem to be the only ones that match. Thats when the plot thickened. 
      Reverse works fine but when in the forward gears it would not go past 1st and was hard to get into neutral. ie. a it took a million clicks up to thump into 1 and as many down to find neutral. still never getting past 1st. within minutes i could hear metal screeching and whirling around in the clutch side of the motor. I took the cover off to find that 3 out of the 4 springs on the centrifugal clutch had broken and were shredded. Also the black mechanism that the pawl on shift shaft grabs moves was loose so it wasnt always grab to change the gear on the transmission. I tightened that mech, and replaced the springs assuming it would solve the problem since the gears were not actually changing from the lever and the carrier should obviously not only have 1 spring left. 
      After putting everything back together it did go into 1st fairly easy but then i again couldnt get it back to N without a million clicks down and couldnt get it to go past 1st. I did one time get it into a higher gear who knows what one but i gained some speed and dropped rpm.
      If i jack both the front and the back wheels off the ground and run the motor it becomes much easier to shift and i can get it to run through the gears pretty well. Usually going into N without a huge fight. not perfect but it does hit neutral and roar while spinning the wheels instead of gain rpm and with the power. 
      I have tried every possible position on the clutch adjustment screw without any noticeable result. I think this could potentially be where my problem lies at this point.
      does anyone know if the case is supposed to be threaded? because mine is not. obviously it seems as though it should be since every other bike ive touched has been. i even took the cover off my quadrunner to make sure it wasnt crazy.
      when the screw is adjusted and the jam nut tightened the screw will just slide back out since there is no threading in the case. accomplishing nothing. 
       
      Does anyone have any insight on any of this? Are my plates stuck, Centrif clutch worn out, case stripped or something else crazy im over looking? 
       


    • By MarkinAR
      So this 98 Big Bear is my new project.  While I'm waiting on a few parts to show up, I'm working on a few small things.  I can shift 1-5 just fine, no problem at all (keep in mind, this is not running yet so just manual shifting sitting still).  However, I can't shift from 1-neutral.  I can hold down on the foot shifter, rock it a bit, and it will disengage the clutch so i can push it around in neutral as long as I keep pushing down on the shifter.  However, it will not downshift to neutral and stay there.  I know BB's have had some shifting difficulties in the past, but before I dive into this, have any of you fine folks encountered the same issue?  I'm tempted to just adjust the linkage a bit since these have an external linkage, but thought I'd toss the question to the group and see if there are any common issues to look for.
      Thanks guys...
    • By MarkinAR
      Picked this gem up today for two Benjamin's. Bike is complete, just worn out all over. Should be able to get the plastics back green, need to fix the shifting as it doesnt go into neutral, carb has been off 6 months but the intake was plugged off and he had an OEM carb that just needs rebuilt. Rear brake drum is completely seized in the open position. Normal relay, solenoid, wires are trashed. Think itll take about $100 to get it rideable which isnt bad for a $900ish bike. 

  • Similar Tagged Content

    • By mikeexplorer
      Wiring diagram for 2007 Arctic Cat 700 EFI 4x4
       
       
    • By sloundez
      Does anyone out there know where I can get a functional pair of wheel cylinders for subject ATV? Any suggestions welcomed. Thanks
    • By marcuslachance
      I
      I bought a Honda 250sx 1986 but the exhaust is broken. Apparently it's not possible to order a new one. I checked to order one on others compagny but there's noting.
      Do you know which exhaust it's possible to install. Is there a company who sold an exaust to fit on my 250sx.
      Sorry for my english
      Thank you
      Marc
    • By Npeters
      Im working on a old 1987 honda 125 4 wheeler in the school shop. It will start by getting pulled by another 4 wheeler but wont start with the pull start or Electric Start. When you pull start it it tries to start but when you try the electric start it just turns over but doesnt even act like it wants to start. The spark plug is dry and it shoots fuel out of the back(air filter side) of the carb. Weve had the carb off twice and it is complety clean. What are some things we can try?
    • By Kingquad1
      Hello I am new hear. I just purchased a 1998 Big Bear. It was sitting for 3yrs in storage. The guy I bought it from got the carb cleaned and it runs good. I am having problems with the neutral light. When I shift into neutral the light does not come on. If I mess with the gear shifter, I can get it to come on so I can start it. I can still pull the hand brake and start it that way. I cant find the neutral safity switch on this machine. Any suggestions would be great.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...