Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

ghoeltin

2000 Suzuki Quadmaster 500 four wheel drive pops out of gear

Recommended Posts

When my atv is put in 4 wheel, it makes some growling noises and then kicks itself out of gear. Has anyone had the front end apart with a similar problem?

Share this post


Link to post
Share on other sites


yes i have. i have the exact same machine. you will most likely need a complete front diff rebuild. if it pops out of 4x4 then either the lock up sprague or the detent ball and spring aren't working. At any case I highly recommend pulling the diff out and pulling it apart before you have a catastophic failure. I left mine to long and it cost me a complete front end. Send me a comment if you need any extra help. I would purchase a factory manual for the machine. i have both and the clymer one tells you squat for info.

your friendly neighbourhood mechanic.

Share this post


Link to post
Share on other sites

A bent shift fork may be a possibility too, but if you only have the problem when you shift into 4wd, gearhead may be right. Good luck.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Michael Kastanis
      Hey I have a Kawasaki 300 boyu and it die in 5 gear and can’t get in Neutral try rocking it and moved it back and forth but nothing can same one here help me pls

    • By Cj Winds
      I have a 2005 Yamaha Kodiak 400 Automatic. It has an oil leak inside clutch cover. The middle gear has two oil seals, the front seal is leaking engine oil into clutch area. How do you change the leaking seal?
    • By dirtjunkie85
      Just wanted everyones opinon on riding glove I do long desert races and none of the glove i have wore seem to hold up really good they always wear fast and dont do much to prevent blisters any advice thanks.
    • By John Victor
      My father-in-law gave my boy a 1999 350 Big Bear. It's been sitting in a barn for a bunch of years. It runs great! My boy has been riding a couple weeks now and it has developed a squeal coming from the front end when you get off the gas at speed. No noise during acceleration. At first I thought brakes. I took it for a ride and I don't think it is the brakes. I feel it is the front prop shaft U-joints, front differential or one/both axles. I pulled the fill plug on the differential and I can't find anywhere how much gear oil should be in there. My gut says up to the fill opening. It doesn't have a manual. It's wet in there, just don't see any gear oil.

      #1 Should I fill the differential with gear oil up to the fill opening?

      #2 How do I check or know if the u-joints are bad? That looks like a "Big Bear" of a job if they don't need to be replaced.

      #3 What else could it be? I don't think it is the front bearings. I jacked the front wheels off ground and no play in the right wheel. Very little play in the left wheel, looks like the lower control bushing is where that play is coming from. The rubber CV boots look original but all still intact. Wheels spin easily without any noise.

      Thanks for any help!
  • Similar Tagged Content

    • By Aj Hurtibise
      I have a 2000 Honda trx90 I got from a buddy for free he said it needed a carb so I put his old carb back on it to try to get something out of it and it does not have any Spark. I already replaced the ignition coil I don't know much about four wheelers but I am a technician so I do know my way around a motor any electrical help would be wonderful or specs I don't have the best digital multimeter either.
    • By JPEDRO
      So when im ridding in high gear randomly sometimes it will go into a persay limp mode and only allows a max of 30kmph and it sounds like a rev limiter, what would cause this and how to eliminate this all togeter as in the new ones with the over ride switch. its the sound that it does in low range or reverse. i want this gone period when i get stuck in mud i cann spin tires fast enough. and while im in high gear i dont want this happening. if you need more details the easier way of getting a hold of me rather then the forum is my email [email protected] i dont have time to check back here oftern but i get my emails right away.. thanks guys
    • By Christian Brindle
      I've already posted here once about this ATV. Lots of people suggested i check the cam and after a couple months i finally got around to attacking it. I got it all apart and got the cam/rockers out. I'm almost positive they need to be replaced, they're pretty scored up and don't look too hot. Just wanted some final opinions before i drop the money on it. I'll also take feedback on the new cam i've chosen.
      Old Cam: 
      New Cam: https://www.amazon.com/hz/wishlist/ls/2GM2J05FQQPCD?ref_=wl_share
      Old Forum: 
       
       
      Thank You.
    • By johnwayne
      i have a 2000 suzuki king quad lt-f300f that i picked up as a project bike. it didnt run well when it was parked outside 5 years ago. it cranked after putting fresh gas - but would not run below half throttle, i took apart the carb, cleaned debris, and re-assembled. i suspect that the pilot needle is sheared off - it never protrudes into the throttle body through the pinhole. now to get the bike to ALMOST idle, the throttle idle adjustment knob is all the way up/in. the pilot needle is turned almost all the way in/up (if i understand correct, it should nominally be out 2 1/4 turns or so). and like i said, it will ALMOST idle. floods easily, rides rough.
      wanted to hear from those more experienced than me with suzukis - and im self-taught atv repair, so dont laugh too hard if my verbiage/part names is way off. 
      facing the driver's side of the bike [US] there are three hoses on this side of the carb. without a service manual or way of knowing what was messed up before i got it, i think i have them right: front hose as a vacuum to the petcock, middle hose as vacuum to the fuel pump, rear hose as fuel line from the fuel pump. running the bike in prime position results in flooding even while riding. with all hoses disconnected from the carb, fuel slowly drips from the vacuum line connected to the petcock.
      so just my speculation is that the diaphragm in the petcock is split, and the pilot needle is broke off - causing my inability to not quite idle and the rough ride. this suzuki is hoses and cables everywhere compared to the honda ranchers and yamaha warriors i am used to. I would like to have a plan rather than: replace everything at once.
      is my speculation on the right track, or could something else be at play? say, if the compression was non-existent, would that cause non-idling? i am all ears, look forward to the input.
    • By skymankila69
      I traded my dirt bike for a 2000 arctic cat 500 semi automatic. when i went to go pick it up the guy said it didn't get spark, so i thought it was going to be something simple like a coil. well it wasn't. first thing i did was take all the plastics off to get easy asses to every thing. so i bought a brand new battery for it seeing if it got power, it didn't. the dash wouldn't light up neither would the lights, so then i tried to see if the starter worked it didn't so i jumped the solenoid and the starter started turning over the motor. so i bought a new starter solenoid, when i installed it the electric start still wouldn't work , so i bought a new kill switch and starter switch that goes on the handle bars, when i installed it, the electric start still wouldn't work. so then i went to see if i could get spark by pull starting it, i didn't get any spark, so i bought a new spark plug, and guess what, still no spark, so then i bought a new coil for it to see if that would fix it. so i installed the new coil and guess what no spark still and still no power to the dash. so to sum it up i'm not getting any power any where to the four wheeler. so i cleaned all the leads and plugs and still nothing. so then yesterday i took the wiring apart to see if their was any frayed wires, and no their wasn't. does any one have any ideas what this could be i'm up for anything. also if any one knows how to bypass all the wiring just to get it to start i open to that to, or if someone knows where  i can get a wiring diagram.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...