Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

KCOLLIS

2007 King Quad 450 idle air screw setting

Recommended Posts

Hi all,

I have a 2007 king quad 450 with starting/idle/power problems. My two boys had a go at it while I was away at work and now I found that the idle air screw was removed and I don't know about setting it up. I want to set this before I start on the other problems. New fuel pump, new injector, new foam air filter, error code reads -C00. Any help would be appreciated.

Share this post


Link to post
Share on other sites


Do you still have the screw? I don't believe it is an air metering screw, I think it just moves the throttle position to adjust the idle. Look and see what the screw does, does it move the butterfly valve when you turn it in? If it were me, I would start by screwing it in just short of opening the throttle vavle. If you need to open in up more, you should be able to make that adjustment on the throttle cable adjustment on the bars. Go with the most simple things first, if you don't have a repair manual, get one.l

Share this post


Link to post
Share on other sites

Thank you for the answer. It is an air regulating screw in the fuel injector throttle body. It allows more or less air to pass through to the fuel mixture. The manual says not to mess with it but it was already messed with and I don't know the factory setting. I hope someone can help with this.

Share this post


Link to post
Share on other sites

It couldn't hurt to call a dealer tech and ask them how to set it properly. Don't let them talk you into bringing it in to them. If they won't give up the answer, get a factory Suzuki repair manual, it has all the info that the dealers do, and it is cheaper than an hour of their labor. The crappy thing here is, you need that to be correct before you can even begin to address any other problems.

Can you access the screw with the throttle body on the quad? Would it be possible to adjust it with the engine running? That would be ideal because if you can't find the info, you could just set it to 1 1/2 or 2 turns out from seated and fine tune it with the motor running.

Were you having other problems before your kids started messing with the machine. If you think the injector may be part of the problem, you can take it out and inspect it visually. I have heard of people having problems with cracked injectors. Also, there is a temp sensor in the airbox, make sure the plug is secure and the wires aren't damaged. Probably wouldn't hurt to check wiring on any thing you may think is not working properly. I know I have found several wires on my LT-R that have wear spots on the insulation and I have had to tape them up. Good luck.

Share this post


Link to post
Share on other sites

Thanks DirtDemon,

I'm going to call the dealer today. I need to know the factory setting because I was having other problems and need the origional setting on the air screw before troubleshooting the other stuff. Hard to start, rough idleing, and poor power under load is making me think valves but I would like to try some other stuff first. My compression tester won't fit the small spark plug hole so I'm going to try and figure out how to use my vacuum tester on the valve manifold.

Thanks again, Ken

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Shane Pillar
      Talk about what kind of atv you have and what you do with it.
    • By fox300exchic
      Let's hear all there is to know about you ladies! Where your from and where you've lived. Kids or no kids. What you do for a living. Why you ride and how you got started.
    • By davefrombc
      View File Quad Runner 250 King Quad 1987 - 1998
      Service manual  for  King quads  250  and 300
      Submitter davefrombc Submitted 01/28/2017 Category Suzuki ATV  
    • By MarkinAR
      Working on my oldest son's buddy's 2000 Big Bear.  He was having some power loss at WOT so i thought it worth while to clean the carb and put at kit in it...or at least clean the OEM jets and use the new orings that come in the kit.  It starts and idles like a champ, but dies and wants to backfire with any throttle at all.  I assume lean because it will run decent with the choke on. Air screw adjusted fine, nice crisp idle.  This one has fuel/air screw, low speed jet, mid jet, and main jet.  I was assuming just trash in the low speed circuit so pulled it and cleaned again, still does the same. 
      Two questions I guess:
      1. Does it sound most likely trash in the off idle circuit?  This one has a few more passages and jets than I'm used to...and a darn diaphragm.
      2. It now really wants to leak at the bowl drain screw.  It doesn't seem to tighten enough to completely stop the flow.  Seat looks good, screw was dirty but cleaned up fine with a touch of 2000 grit paper.  First for me.  Any idea here?
    • By Ryann Racho
      So Id say about 2 years back I bought a 2013 Polaris Sportsman 500 H.O. off of my uncle. It ran perfectly, nothing wrong at all. I usually go mudding with it or just ride trails with buddies. So as you would assume, the quad is quite dirty from sitting for a few weeks.
       
      STUTTERING PROBLEM: I noticed one day out of nowhere that in high gear at 15-20 MPH, I was already maxed out at 4500-5000 RPM  It would get to 15-20 mph, max out on rpms and start sputtering. It sounded like it was basically acting like it couldn’t go any faster than this.
       
      IDLING PROBLEM: I was fucking with the carberator the other day maybe thinking that is causing my sputtering, and now my idle will shoot up to 2600 on start usually, then I will turn the throttle adjustment down to the normal 1400. The rpms with then fluctuate 10-30 rpms back and forth repeatedly, it will then run for about another 30-60 seconds and the RPMs will slowly drop to about 900-1000 RPM and stall out. I replaced the carburetor and everything seems to be working perfect on that, no leaks and what not but it’s still acting strange. Also, I’ve noticed that when looking into the Electronic Throttle Control that two plates that aren’t supposed to touch have to be WAY past touching to even try to fire up. Even when set at a wide open throttle like that, I still have to give it some throttle to get it to fire up.
       
      Here is what I have done so far: 
      Checked the belt and clutch
      Changed out spark plug (Last one was covered in carbon)
      Cleaned the intake and air box
      Replaced the carburetor
      Replaced the inline fuel filter
      Checked that all lines on carburetor are connected into the right spots
      Checked If intake boot was cracked (Not from what I can see)
      Unhooked and reattached new carburetor (About 4-5 times)
      Cleaned battery terminals and battery off
      Shut on and off Gas Line Cutoff Valve
       
       
       
      My next thoughts are that maybe the TPS is fucked up or maybe the Spark Arrestor is plugged with mud. I was thinking tomorrow to purge the exhaust and also check the ohms output on the TPS.
       
      ANY HELP IS GREATLY APPRECIATED. I HAVE BEEN BATTLING THIS FOR WEEK AND REALLY WANT TO GO RIDING. THANK YOU!
  • Similar Tagged Content

    • By mikeexplorer
      Wiring diagram for 2007 Arctic Cat 700 EFI 4x4
       
       
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By crazynordlander
      Hi All,
      Has anyone found engine oil in their air filter box. The must be little or no baffle between crankcase ventilation and that hose that attaches to the air filter box.
      I went to pick up my ATV today 60 miles away that they could not fix the jerky low speeds on and before I loaded it decided to check on this. Sure enough there was a good coating of oil with some pooling in the bottom of the air filter box. The air filter has oil on it too but is it a dry element or oiled element type. My guess from the color of it dry.
      I heard on a comment on my YT videos that there is a kit for this issue? Is this a CFMOTO fix?
      Thanks
      Kevin
    • By skgw1
      Feul pump went out. Replaced. At times quad cuts out like its not getting gas. Saw article on new pump needs to be calibrated. Told how to go into a service mode. Does not tell how to calibrate after going into mode. Can anyone shed light on this procedure.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...