Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

berryjo5

1986 Suzuki lt230s full throttle problems

Recommended Posts

hey guys,

im new to the forum and i need some information im hoping someone can help me out with. i have an 86 suzuki lt230s that i just did a full rebuild on. basically new everything including a new high flow air filter and a new high flow exhaust as well as a carb rebuild kit. I got it running very well until i give it full throttle in which i lose all power and it acts like it wants to stall. I richened the mid range mixture almost all the way after several attempts of being a tuning problem and it seems to have improved it but it still isnt 100 percent. Anything after about 7/8 throttle and this problem occurs... based on what the book says i either have it too lean yet (which may be the case cause im trying to get it running in 30 degree weather) or i have the wrong jetting in my carb (which i hope isnt the case). It is a possiblity that it is still too lean with the cold weather, the high flow air filter, and high flow exhaust... does anyone have any suggestions for me?

Im just not too sure of the jetting options i have other than stock due to the age of the quad in general.

thanks fellers,

john

Edited by berryjo5

Share this post


Link to post
Share on other sites


You need to run richer jetting with higher air flow and aftermarket exhuast. You will likely need to go up a few sizes on your main jet, after installing the bigger main jet, you can probably move your needle clip back to a leaner spot. As for the pilot circuit goes, you should be able to get the adjustment you need by turning the screw out a bit, if you can't get rich enough by adjusting the screw, you will want a bigger pilot jet. Also keep in mind, if you are running with a modified airbox lid, or no lid at all, you will need to go even richer. BTW, I am going to delete your post in the other thread, since you have your own thread here. Good luck.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Frank Angerano
      So i took a road trip today to look at a Suzuki Eiger! 2006 in perfect condition other then the fact it starts for 30 seconds and shuts down.  
      Its been sitting for about a year in a shed. 
      It has a plow and a winch included!!!
      Got it for a really good price and all looks good so far.  
       
      Stay tuned.  





    • By Ryan Foster
      I am trying to find a used OEM cylinder for the above mentioned quad. I was told the current cylinder came from Amazon so I suspect its aftermarket china (made from recycled coat hangers and shopping carts.) Anyway, was looking at the parts list and they have 2 cylinders listed..
      11210-19B82-0F0
      MODEL X/Y
      and..
      11210-19B90-0F0
      MODEL K1/K2

      My engine case is stamped K403 230829 Trying to figure out what model I have. I see I have a K in there but....
      I don't know what the differences are between the cylinders (the first one cost more). Anybody know how to decipher this?
      I only have the engine, I don't have the frame to get the actual VIN.  

      Also, are there any marks on an OEM cylinder to differentiate it from aftermarket?
       
    • By Mike Hooper
      Hi everyone! I'm from New Zealand, and doing up a Suzuki Lt50 for the kids. This is the first bike I've ever worked on, and it's currently not running. Hoping that both Google and this forum will get me through! Haha

    • By Amazon Ads
      Where do you buy your ATV parts? Did you know that Amazon has ATV parts in stock for immediate delivery? You'll find all the best ATV parts and for great prices! Check out all the ATV parts available with free 2 day shipping now...
    • By Randel1
      I am trying to put a 1994 Suzuki 250 quadrunner back into service. I have it up and running like new but need to replace the plastics as they are brittle and crumbling due to age and sun exposure. I would like to purchase new parts either OEM or aftermarket but have had little luck in finding them. I would even consider used or salvaged parts in serviceable condition. Any help in locating these parts would be greatly appreciated. Thanks in advance.
  • Similar Tagged Content

    • By oxidized_black
      these are what i have in my collection ... always looking for more
      1985 - 1990 Suzuki LT230 & LT250 Service Manual
      https://www.quadcrazy.com/files/file/532-1985-90-suzuki-quadrunner-lt230-service-manual/
      1987 - 1998 Suzuki Quad Runner 250 & King Quad 280 Service Manual
      https://www.quadcrazy.com/files/file/268-quad-runner-250-king-quad-1987-1998-service-manual/
      1987 - 2006 Suzuki LT80 Service Manual
      https://www.quadcrazy.com/files/file/89-1987-2006-suzuki-lt80-service-manual/
      1987 Suzuki LT500R Quadzilla Service Manual
      1988 - 1992 Suzuki LT250R Porting Instruction
      https://www.quadcrazy.com/files/file/90-1988-1992-suzuki-lt250r-porting-instructions-manual/
      1988 - 1992 Suzuki LT250R Quadracer Service Manual
      https://www.quadcrazy.com/files/file/91-1988-1992-suzuki-lt250r-quadracer-service-manual/
      1988 - 1992 Suzuki LT250R Tuning Guide Instruction
      https://www.quadcrazy.com/files/file/92-1988-1992-suzuki-lt250r-tuning-guide-instructions/
      1999 - 2004 Suzuki King Quad 300 Service Manual
      2002 - 2007 Suzuki 500LTA Service Manual
      2002 - 2009 Suzuki LTF250 Ozark Service Manual
      https://www.quadcrazy.com/files/file/94-2002-2009-suzuki-ltf250-ozark-service-manual/
      2003 Suzuki LTZ400 Service Manual
      2006 Suzuki 50LTZ Quad Sport Service Manual
      2004 Suzuki 250LTZ Quad Sport Service Manual
      2005 Suzuki LTA700 King Quad Service Manual
      2007 Suzuki 90LTZ Quad Sport Service Manual
      https://www.quadcrazy.com/files/file/97-2007-suzuki-90ltz-quadsport-service-manualpdf/
      2008 Suzuki 400FLTF King Quad Service Manual
      https://www.quadcrazy.com/files/file/98-2008-suzuki-400fltf-kingquad-service-manual/
      2008 Suzuki 750 King Quad Service Manual
      https://www.quadcrazy.com/files/file/99-2008-suzuki-750-kingquad-service-manual/
      2009 Suzuki 400LTZ Quad Sport Service Manual
      https://www.quadcrazy.com/files/file/100-2009-suzuki-400ltz-quadsport-service-manual/
       
      ALSO CHECK SUZUKI ATV SERVICE MANUAL DOWNLOADS
    • By mrfartsalot
      i have a 2001 suzuki quadmaster 500 4x4 that the primary cvt clutch is rusted on any ideas on how to get it off i want to try to reuse it if possible.
    • By oxidized_black
      tag : zukifreak
       
       
       
    • By Jason Magnone
      As stated above working on a 1999 Suzuki LT-F160. I think I’m having trouble with the carburetor. I keep fouling spark plugs. Full disclosure, I did make a poor attempt to “rebuild” the carb (that’s why I think that’s the issue). No idea if the new parts are at the correct “settings” (gaps and such) I believe the starting point is 1.5 turns from bottom out on the adjustment screw (is there another adjustment I don’t know of?).  Doesn’t feel like I’m getting gas drawn through the carb (clogged jet maybe?), the plug isn’t wet at all (assuming why they’re fouling?) Not a great deal of experience working on carbs and not having much luck on finding a lot of info on the 160’s.
      1st- by chance can I swap out the original carb (13200-02C03) for an LT 250 model (think the HA01050). They’re only about $30 apposed to $200. That would at least narrow down if it’s a wiring problem or carb issue.
      2nd - The wiring has been minipulated at least a dozen times (before I acquired it, my cousin got it from a buddy kind of thing). Hopefully don’t have to dig into this too much as it’s currently a bit if a mess. 
      I was told it ran last year... 
      Any imput would be greatly appreciated
    • By Ajmboy
      Pretty good video on the history of Suzuki ATVs if you are interested in some ATV education. Starts off from when three wheelers were the norm.
      Suzuki, A company with about 100 years of manufacturing history is company built on bold innovation and the courage to push forward with new ideas. One of these new ideas was created in 1983, when Suzuki invented the first four wheeled ATV and introduced it to the world. At the time three-wheeled ATVs were the norm, and Suzuki’s four-wheeled ATV the LT-125 created an al-new vehicle category and literally changed the industry.
       
       
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...