Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

wimpster

2005 arctic cat 400 automatic

Recommended Posts

HELP! I am in desperate need of either a carburetor or a rebuild kit for this bike, arctic cat says that the fuel diaphragm is on back order. Any advice or help would be great!

Share this post


Link to post
Share on other sites


You might try e-bay for a decent used carb or possibly even a carb kit, also, you may try going through some online parts retailers to see if they have the parts handy. Good luck.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By barracuda420
      Hi, I'm new to ATV/UTV's and am looking for any advice that would help to repair my 2018 Ranger 500.  I got it from an insurance auction and have never owned one before.
      It looks like it was sunk deep.  Found rocks and sand in the roof, milky oil in the air filter box, water in the fuse box, etc.
      So far, I've cleaned the air box out, vacuumed most of the rocks and sand, checked the engine, trans and diff casings for cracks/leaks.
      The battery would not charge while connected so I know there is some short somewhere...probably the wet fuse box.
       
      I plan on drying out the fuse box and all connectors with a hairdryer tomorrow, check the fuses, remove/dry out the ECM and disassemble/clean the air intake.  Then install the battery and see if i can get it to key on and see what kind of lights I get.
      Need to know what to expect with the engine/trans...
      Thanks.
       
    • By Nick Brooks
      Working on a 2002 Quest 500 and the grommets in the tank are rock hard and leak.  Any tips on replacing without having to pull the tank, hands are too big to get to the bottom gromment which is the worst one.
    • By Frank Angerano
      I’ve decided to post  a thread on the process of cleaning a carburetor and what’s needed in order to do it properly.    There are some members that are new to this and are not very versed in doing so. I want to help and feel this might explain things better. I would hope this helps you along.     We all have our own little tricks of the trade so I’m sharing my process on how i break a carburetor down, clean, reassemble and adjust it to peak performance. I welcome any other members input on this topic.     List of things I use:   Safety glasses !!!   Rags.   I like to use old white Tee shirts or I buy and always have a few white pillow cases from the dollar store on hand. The cheap ones.     I like to use a frisbee turned      upside down like a bowl to keep the liquids to a minimum on spillage to the work bench.    A set of cleaning picks and brushes or a piece of bicycle break cable, I separate the strands and use them to clean out the tiny holes in the jets. (Pic attached)     A can of gum out  carburetor cleaner with the small red tube that attaches to the spray tip.  (Pic attached)   A can of compressed air, the kind used to clean out keyboards on computers. It also has the small red tube that attaches to the spray tip.  Or a compressor if you have one with a blow out tip.  (Pic attached)   A piece of clean hose that I can connect to the fuel line port on the carburetor to test the float operation. About 10 inches long.    A few Q tips.   The process: I like to put the pillow case down on the work bench and spread it out flat.   This really helps in being able to keep track of parts. Especially because it’s white.     I use the frisbee because it’s small enough to keep parts contained and durable enough to deal with the chemicals and any gas that will come out of the carburetor while opening it up.     It’s important to make sure you keep track of where everything came off and where the screws and parts all go back.     I like to start at the bottom and pull the bowl off. I immediately spray the inside of the bowl down with carb cleaner until its about half way full and set it aside.   Then I take the float out and check it for any fluid inside. If it’s a white color float you can hold a flashlight under it and see through it for any fluid inside.  If it black just shake it up and listen for fluid inside. No fluid inside is a good thing !    When the float comes out the fill valve needle will come with it. I take that needle and put it in the carburetor bowl that I filled with carburetor cleaner. This way it soaks for a bit. I do the same thing with the jets also once they are unscrewed and out toss them into the bowl to soak.    Take the air/fuel mixture screw out and soak that as well.  Side note: the air/fuel screw should have a screw, spring, washer and o ring.    After all the jets and parts are out and soaking I like to take the carburetor cleaner, use the small red tube and stick it in all the little holes/ports on the carburetor and spray.   I do this while it’s in the frisbee. This way there is no mess. I look to see where the spray pressure comes out on the other side of that port.   Once this is all done I start running my brushes and cleaning tips gently through all of the holes/ports and spraying it again with the carb cleaner.  After I feel I’ve seen a clear flow of fluid through all the openings I spray them with the can of air the exact way I did with the carburetor cleaner. This will blow out any left over junk that’s still in the carburetor.   Check the choke operation is working properly and spray it clean. Most choke devices are easily cleaned up so hit it and move on since they are mechanical and it’s just a matter of freeing them up, spraying with cleaner and lube.   There are multiple types of chokes but many of them for the most part are mechanically operated.    Once this is completed I wipe the entire carburetor down good and blow it clean and set aside.     I then start working on the jets one by one. Start by running the cleaning tips and brushes through all the tiny holes making sure they are all clean. Hit it with the carburetor cleaner and then air. I hold a flashlight to it when it’s done so I can make sure all of the holes are clear. I set all the jets aside on the work area.  Do the same thing for the float needle and air/fuel screw.    Now once this is all complete you can set the frisbee aside and start to reassemble the carburetor on the clean white surface.   I start by running a Q tip in where the fill needle sits into the carburetor. Some carbs have a small o ring that needs to be clean for proper seating of the fill needle.     Carefully reinstall the jets where they came from and do not strip or over tighten the jets and use the proper size screwdrivers when removing and reinstalling the jets.    Reinstall the air/fuel mixture screw and set it to what’s called out in the manual for that bike.    Install the float and fill needle assembly.    Now in order to test that float I like to take that piece of hose I mentioned and connect it to where the fuel line gets connected to the carburetor. I then turn the carburetor over to the upright position and blow into the hose. You should hear air coming out of the bottom of the carburetor. While blowing, lift the float up and the air should stop.  Let it go and the float should fall down opening the fill valve and you should hear air again.  The air should stop about 3/4 way up when raising that float while your blowing air into it.   If so then your good to go. If not make an adjustment    Set the carburetor down, take the bowl and empty it.   Clean it out and scrape/wipe any old junk inside and blow it out good.   There is a screw on the outside of the bottom of the bowl. Remove it and clean it out and reinstall.     Turn the carburetor over and reinstall the bowl. Tighten the screws in a crisscross pattern so the bowl seats evenly.     I like to put the hose on one more time and do a float test to make sure it’s opening and closing properly. All you have to do is blow into the hose and run the carburetor  upside down to see if the air stops.     Reinstall the carb and you should be good to go!    All pics of the items I use are attached below.   If you understand this great. If not ask away! Don’t be shy and don’t cut corners.   You will only wind up pulling the carburetor off of the bike for the third and forth time before you get it right.    The last thing to be discussed is dialing in the air/fuel screw when your finally put back together and running.  This is a relatively easy task.   Again I hope this helps!    Frank.     


    • By technofarmer
      Something i have wondered for years is about the firing order of a parallel twin.  Yes i am aware of both pistons going the same direction at the same time, but do both cylinders fire at the same time or at different times? Just being curious since i have always wondered.  
    • By Guy Churchward
      I have a 2016 Yamaha Kodiak and find myself with a start issue.. I changed the battery so it’s not that.. here’s a video of me trying and then boost starting.. can anyone give me pointers as to a starter motor issue or fuse or wiring or whatever ?.. I find myself without a vehicle with a tow hitch for the 1st time in years so have a dead and stranded ATV to fix !
      thanks in advance, suggestions welcome
      Guy

      IMG_5952.mp4  
       
  • Similar Tagged Content

    • By Michael Aiken
      Where can I find a wiring diagram for my 2005 450 Kodiak. Thanks.
    • By Mo Salem
      So my front hub broke, I’d like to put aftermarket on. Hard to find new oe ones. Please help. I’m new to all of this, I have some car knowledge and try to apply it
    • By oxidized_black
      tag : zukifreak
       
       
       
    • By LMI
      Was using the quad the other day to shuttle wood from my pickup to my wood pile.  When the job was done I turned off the Quad and heard a bit of a racket from the front end.  When I got down underneath the sound seemed to be coming from the fan housing.  fan was moving in spurts and not quickly... much like a computer case fan that's had it's day.  What I know.
      Temp sensor is ok, as the fan tries to activate fan is getting some voltage as it is attempting to spin.  When I first bought it used I tested the fan direct to battery and it was fine. The fan was working ok even not direct wired as I went on a couple of rides and when stopped and idling the fan did run Seems to be free spinning with my finger read up in the manual and they require me to drop the rad.  now I'm not opposed to that as the rad has some damaged areas I want to try and straighten out.  But if I can get the fan working without, I can leave the rad as it is until next year.
      Fan assembly is about 300 bills, any work arounds or alternatives?  I even thought large computer case brushless fan.  smaller ones are about $7 larger ones better quality probably far below the 300.  They run standard 12v DC.
      Anything I should be doing before dropping the rad... other than check for obstructions even though it seems to spin, and trying to hardwire it to the battery again for a test to see if it acts the same?
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...