Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

MIKEL5469

2001 Yamaha 660 Raptor Axle nut issue

Recommended Posts

My 2001 660 raptor seems to be having some issues with the rear axle nut. Seems like about every 2 rides the rear axle nuts back off and loosen up.I average about 75 to 100 miles a ride and this is driving me insane. The rear bearings and seals have been replaced and the axle has been upgraded to an 2003 axle because i had a mishap with a tree,kind of jumped in my way...lol So i got pissed off and ordered a mod quad double locker after market axle nut to hopefully cure this issue. I would love to hear any input you guys and gals my have. Is anyone else ever run into this issue,and how did you fix it? ,Thanks a bunch

:realmad::aargh::mad:

Share this post


Link to post
Share on other sites


Get used to it Mike your over forty and the older you get the more issues you will have with your nuts, especially not working correctly.

Share this post


Link to post
Share on other sites
that part of me is working awesome.....thank you very much...lol

Sorry to hear your having problems with your nuts :laugh:All I can say is tighten it more I did my bearings on my Honda and the same problem accured Finally we just got out a big wrench and a cheater bar and it worked !!!!

Share this post


Link to post
Share on other sites


* Thread moved to Yamaha forum (was posted in Kazuma forum). Added year, make, and model to thread title.

Share this post


Link to post
Share on other sites

Put an aftermarket axle on and you have to tighten the axle nuts about every moto. The only cure for it is an expensive aftermarket locking nut like what you ordered.

Keep in mind that everytime you crank on the axle nut that you are putting force on the axle bearing. That will eventually lead to premature bearing wear.

Share this post


Link to post
Share on other sites

buy a nut with a locking grub screw, the nut should only be done up tight enough to take the play out of the axle and then locked off with the grob screw otherwise as has been said before it will lead to prem bearing wear

Share this post


Link to post
Share on other sites

It might not look the best but try wrapping duct tape around it. I had to do that on a warrior i had and it never came lose again.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tinscissors 428
      I have a 01 blaster kickstart won’t work but bump start does work
    • By bradley nelson
      Im cool with the police in my area so i can ride on public roads.
    • By StolenATV
      Blue and White Raptor 90
      White, Black and Yellow Raptor 90
      Blue and White WR450F Motorcycle
      VIN’s for ATVs
      RF3AB11Y2HT006593
      RF3AB11Y5HT006815
      Stolen from the yard at my home at night on 10/26/19.
      $2,000 reward for information leading to their return.
      The post Two (2) Stolen Yamaha Raptor 90 ATVs and a Yamaha WR450F Motorcycle appeared first on STOLEN 911.
      View the full article
    • By quadtech62
      I have a 02 Warrior i am trying to build a wiring harness i have looked in the manual and  i am confused... the pick up has 2 wires.  W/R W/G The source rotation coil has 2 wires. One is Red other is white/blue. The manual shows the  the white and blue wire connected to the w/g  right after the stator... so why is these 2 wires connected?  Does not show w/b wire at cdi 
      i have looked at many options with no luck if someone has a 2002-2004 warrior and can take a pic of the wires and location at cdi i would really appreciate it. Thanks
    • By Barry Troxtell
      I have a 2005 Sportsman 500, Instrument cluster will not illuminate, hi/lo beams work though.  Any tips or troubleshooting info is greatly appreciated!
  • Similar Tagged Content

    • By Aaron Wilson
      My 1996 Yamaha Kodiak 400 has a cracked CV Axle boot and the axle wiggles back and fourth if you pull on it. It also clunks if you go from forward to reverse fast with the tires turned hard one way or the other. Im thinking a new axle will solve the problem. Can you guys walk me through the steps of replacing the CV Axle, I have never done anything like this.
      Thanks
    • Guest Fox300exchic
      By Guest Fox300exchic
      If you know you're going to be bashing your quad's axle over rocks and rough terrain, tape it up. Take a roll of electrical tape and generously wrap the axle from the swingarm out to the hubs. Standard electrical tape will work, but the heavy-duty thick stuff is even better. When you are done bashing you bikr though the nasty terrain, you can cut the tape off and still have that showroom shine for your next out to the dunes, where you don't have to worry about getting dings!
      Quad off-road magazine
    • By Alan Callison
      Hello boys and girls!:howdy:I need a little help if ya dont mind.I need to replace the rear axle bearings on my 400 but Im going at this blind having never done it before. Ive looked it up in the repair manual but it doesn't give any specific steps on how to do it. I've got the left rear brakes off already as I was replacing the shoes anyway. Can somebody give me a rundown on what Ive gotta do please?I know I need to pull the right wheel off just havent done that yet. Do I need to take anything apart in the final drive or elsewhere in order to yank the axle out for instance? Which side does the axle come out from,L or R? Any details I need to know will be greatly appreciated.Thanks ya'll!
    • By Alan Callison
      OK everybody,I need some help here please. My 4 wheeler has got a bad wheel bearing I discovered while starting a brake job. Its on the left side. I've never done one and I need some knowledge how to go about it. Am I to understand I need to pull the whole axle out to do it. I've done it once on a car about 30 years ago,lol. I keep looking around for a repair manual but they're hard to find without having to buy it. I looked here on this site but apparently Im too junior a member to be able to download one right now.Bummer!  One other question if I may.When I pulled the drum off the spindle a torrent of water poured out,the brake shoes were covered in mud along with everything else. I mean the drum had alot of water in it. The shoes were so locked up after I removed the springs I tried to rotate one of the shoes and it wasn't easy at all. I noticed whoever had the machine before myself had laid a bead of RTV around the back plate but apparently it didn't work. Isn't there some kind of gasket for this purpose. I saw it calls for a dust shield but surely this wont keep the brakes dry or will it. Thanks everybody.
    • By Darryl Traina
      This bike has a straight axle that is moving horizontally in the housing in both directions about 2 inches. Has anyone had the same issue if so what did it take to repair it?
      Thanks..
      Darryl
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...