Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

superchief

2005 Yamaha Raptor 350 jetting questions

Recommended Posts

i have a 2005 raptor 350se with a K&N air filter and Baffle removed from stock exhaust and i have a aftermarket cdi

i was wondering what i should jet it to right now its stock and when i fisrt start it up and give her some gas she pops so i need some recommendations on jetting

Share this post


Link to post
Share on other sites


I would think it would need jetted pretty close to if you had a pipe on it... my 02 warrior was running a HMF full exhaust and i was running around a 148-150 so probably one or two under that... If i remember i changed the clip position one notch and went one up on pilot jet... I think i still have my jet kit from when i had my warrior... Should be the same carb and jets if you need some... All of this will also depend on your elevation...

Share this post


Link to post
Share on other sites

so i should try a 146? main? and what pilot? if you can send those that would be great

P.o. box 434 windham ohio 44288

elevation is 980ft

Share this post


Link to post
Share on other sites

well im not for sure...I think they are jetted a little richer than my warrior was... I was at 148 and i had open air box and full exhaust.... ill do some more looking and c what i can find... What is the stock jetting on them??

Edited by jigolbeep

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By MarkinAR
      Can you believe this thing blew a new head gasket after a few weekend rides? Granted, it was beat on in a mud hole every weekend, but this is a new head gasket on a 400 Kodiak. Bummer. 

    • By Adrian Ciotinga
      So I’ve had this quad for the better part of a month, and it’s been hard to start since the day I bought it. Once it warms up it idles just fine and has plenty of power and starts no problem, but cold it takes 20 seconds minimum of straight cranking to start it.
      It’s not really too big of an issue, I’m just curious as to why it takes so long. Earlier today, it took me about 2 minutes of on/off cranking to get it to fire.
      i have attached a video of a cold start to show you what I mean.
      FullSizeRender.mov
    • By Venom
      Hi All,
      I did a total restoration on a 2003 Yamaha Raptor 80. Rebuilt the engine and tranny.. Started it up today and it runs great. Took it for a ride and the transmission worked perfectly. Adjusted the carb a little more and went for another ride. It ran awesome, pulled into the workshop shifted into neutral ( Neutral light came on) and shut off the bike. went to roll it and noticed she would not roll. Turned on the key and neutral light was on... After some troubleshooting I found that she is in first gear with the neutral light on and will not shift into neutral... It seems to up shift fine into 2nd and 3rd and then back down to 1st. I am hoping somebody can shed some light on what is happening... Thanks for any help...

    • By Venom
      Hi, All

      I started this project a while ago.. I have decided to make one thread I can continuously update..

      So , here we go. I got this Raptor 80 in really bad condition.. Rear end frozen, Engine toast, tires dry rotted, tons of rust..etc.. They admitted they beat on it very hard.

      Since they do not make these with a drive shaft anymore I decided to restore it from top to bottom..

      These are photos of when I got it home.

      Next up, the tear down..



      First, I needed to tear it down and determine if the rear end was still good... As we all know... That is where it would be cost prohibitive to restore if it is trashed..

      Got it completely stripped down and I lucked out... The rear Drum brake was caked solid inside with dried mud. That was causing the rear end to lock up. Took off the rear brakes and the rear end spun perfectly smooth.

      Once I got it all stripped apart I needed to take the finish off all the parts. I am going to be powder coating the frame and many parts.. Once the finish is off each part it will need to be sandblasted to white metal .. The guy I use for powder coating gives me a hefty discount if I bring the parts to him ready to go.

      You could just sand blast, but that would take a long time to get the finish off. First I used Aircraft Paint Remover.. That stuff is pretty toxic Goggles and Resperator are required. That quickly gets you down to the metal... Then you can sand blast to white metal pretty quickly...


      I had another thread I had started about a problem with the tear down... It has some great info .... here is the link... It is about removing the frame bushings. ....
       
      https://www.quadcrazy.com/atvforum/topic/14209-raptor-80-frame-bushings/?tab=comments#comment-104702
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
  • Similar Tagged Content

    • By Michael Aiken
      Where can I find a wiring diagram for my 2005 450 Kodiak. Thanks.
    • By Mo Salem
      So my front hub broke, I’d like to put aftermarket on. Hard to find new oe ones. Please help. I’m new to all of this, I have some car knowledge and try to apply it
    • By oxidized_black
      tag : zukifreak
       
       
       
    • By LMI
      Was using the quad the other day to shuttle wood from my pickup to my wood pile.  When the job was done I turned off the Quad and heard a bit of a racket from the front end.  When I got down underneath the sound seemed to be coming from the fan housing.  fan was moving in spurts and not quickly... much like a computer case fan that's had it's day.  What I know.
      Temp sensor is ok, as the fan tries to activate fan is getting some voltage as it is attempting to spin.  When I first bought it used I tested the fan direct to battery and it was fine. The fan was working ok even not direct wired as I went on a couple of rides and when stopped and idling the fan did run Seems to be free spinning with my finger read up in the manual and they require me to drop the rad.  now I'm not opposed to that as the rad has some damaged areas I want to try and straighten out.  But if I can get the fan working without, I can leave the rad as it is until next year.
      Fan assembly is about 300 bills, any work arounds or alternatives?  I even thought large computer case brushless fan.  smaller ones are about $7 larger ones better quality probably far below the 300.  They run standard 12v DC.
      Anything I should be doing before dropping the rad... other than check for obstructions even though it seems to spin, and trying to hardwire it to the battery again for a test to see if it acts the same?
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...