Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

JohnP3

1989 Suzuki LT250 4WD Too Much Fuel

Recommended Posts

I am a retired HD mechanic, I bought a Quad, it over fuels, I have set the Float it has the 31 mm carb so there are no external adjustments, The vent line from the fuel bowel, where does it go to or does it just hang down. The vent line for the fuel pump, is OK. I re torqued the head and set the valves.

I have checked the ignition all tested good.

Feels like the choke is always on , but the brass piston with the needle on the end seems to be sliding free.

I bought a manual It is close to useless, it only shows the 29 mm carb, and does not show the hose routing, or I do not know where to look.

I understand carburetors on Vehicles, this one is totally new to me?

Share this post


Link to post
Share on other sites


The carb breakdown link you gave me is not what I have when I went to pit stop.com it has a picture of the carb I have and it calls the hose a vent, But it shows a "T" and does not show were the other hose is or where it goes.

Share this post


Link to post
Share on other sites

It has the 31 carb on it and was told the slide if worn would cause a problem Bought a new slide diaphram assembly, new float and set it to 13mm, new pin and tube the pin goes in that the jet screws into. It will kick but not run.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Rich1028
      Leota Quad Trails
      4-5-20
       
       
    • By LOGAN WARNER
      Hello everyone, I’m new to this forum. I have a 98 king quad 300, I cannot get it to run right. It will start up and run for a little bit but then it starts sputtering when you give it throttle. It appears to me that it is getting to much fuel. 
      this is what I have done to it: new carburetor, new fuel filter, adjusted the valves.
    • By JacobSlabach
      I have a gentleman that asked me to service his bayou for him.  I have always wondered what oil should be used in atv engines?  Pros?  Cons?  What weight should be used in what type of weather?  Is there one kind that I could bulk buy and safely used in any quad I worked on or owned?  What about performance?  Engine Life?  This has always been a 🤔🤔🤔 area for me with quads as far as why you would use one type of oil over another....
      Thanks!
    • By jimsvtx
      I'm working on my brothers' 2002 Suzuki Vinson 500 . It sat for a few years before I got into it. I'm concentrating on the carb - I replaced orings, needle, etc. and soaked jets, bowl and anything that I could get off the carb that the solution wouldn't eat. I also removed the tank and flushed it with hot water - it's clean. The gas cap innards rusted away and the tank had a lot of rust and water in it before I cleaned it. I replaced the gas cap and installed a new fuel valve because the screens were broken in the old one. The bike will run but spits and sputters and backfires. If you "open it up" it falls on its face and stalls - but starts right up. Here is a link to an exploded view of the carb: Ohio Honda Yamaha Motorcycle ATV Dealer - J & J Motors - Kawasaki Suzuki Scooter Utility vehicle, parts, accessories, apparel
      Can anyone point me in the direction of the problem? It may still be a "clean carb parts issue" . My problem is that the parts list doesn't identify the parts to a degree that I understand. If you said" look at the pilot jet", I'm not sure which jet that would be....See what I mean? It'll run very good if I remove the air filter and cover the opening with my hand and part my fingers a little for the air to get in. Any help is greatly appreciated.
      Thanks in advance, Jim
  • Similar Tagged Content

    • By Guythis448
      Looking for help on wiring up stock wiring harness specifically for a '88 Honda TRX 300 
      If anyone could drop a link or send me a PM it would be much appreciated 
    • By Jers
      I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
    • By Steve1266
      I went out to ride my quad today. When I started it up it ran for a minute, then died. Since then it will turn over but won't start. I've check the spark plug and get great fire. I have had this quad for about 6 months, and very new to breaking it down. But need help. Thanks
    • By suthernboy60
      Since I am not much of a mechanic simple things confuse me. How do you remove the old brake cable for the pedal brake from the frame? Thought I could just pry it out but no luck and not much room to work. Any help is appreciated.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...