Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

cheriah

2000 Polaris trailblazer 250 starter replacement HELP!!

Recommended Posts

Ok guys be easy got a lady here. Yes blonde, but not dumb:yes: Just got the new starter for the quad and wondering if I "really" need a clutch puller since I have to take both primary and secondary out to access the starter? I don't have one. :no:

Has anyone done it without one?? I'm gonna start on this tomorrow am so any and all comments will be appreciated,,,a little nervous bout removing the clutch anyway.....wish me luck!! :biggrin: thanks!!

Share this post


Link to post
Share on other sites


Did'nt need to pull clutchs off ....drained gas, turned bike on side, took off recoil and heat sheild,,,,easy access. It started right up but low compression now so new piston and rings next..ugh!

Share this post


Link to post
Share on other sites

You have to pull the clutch to get to 2 10mm bolts and most of the time if the starter has been replaced they don't put them back in so if you pull the pull starter and remove the 2 bolts each side the Bendix and also the skid plate the starter MIGHT come out if its missing the 2 10 mm bolts on the back side of the starter. You can get the 2 bolts out without removing the clutches it just take a while cuz you can only turn it 1/4 turn but really tough to put back in with the clutches on...and the reason why they are missing most of the time..I don't mind helping over the phone if you need it..Todd POLARISATVREPAIR.COM

Share this post


Link to post
Share on other sites

Thanks Todd, sorry but I was impatient:yes: and did it that way, and it worked well, except for the need to replace the piston and rings now....ugh!! (low compression). I kept the old one going to replace the brushes and keep it for a spare since this is a common thing for this quad it seems (bad starter).

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Michael France
      I have a Kawasaki Bayou 220 KLF220A and I cannot get it to start using the starter button. I have replaced the starter solenoid and the starter relay. I have followed the wiring diagram in the repair manual and it looks like the switch is working well, the neutral and reverse relay have power running through them and appear tp be working correctly. However, I can not find a wire runnng the the starter button that has power on it. Anybody have any idea what the break down is?
    • By Rick Shropshire
      Happy New Year all! Remember not to operate any vehicles while under the influence, you could get busted or worse, you could get hurt or hurt someone else who's playing it safe and end up in jail. Have fun and be safe.
    • By Dale Kermes
      I need some help y’all, I bought a 450r, 2005 and I was riding it and unfortunately got stuck, I had no clutch control at all, I put it in gear and release the clutch, it doesn’t go anywhere, I select through all gears and it won’t move, i can rev it out, I just bought a clutch kit, but I am sorta new to this whole scene of race quads, I always had a 4x4, so any help will be much appreciated thanks.
    • By MarkinAR
      And the new 300FW is already wounded. Something got in a bind and blew the whole chunk of case out around the primary drive gear at the back of the motor. In the pic you can see the crack along the top...there is a big chunk missing from the bottom. And it won't roll....but the front and rear diffs both seem fine. Unfortunate. This looks to be a bit of a project. Still feels like it will shift through gears so i'm wondering if the ring and pinion just jumped a bit and blew something to pieces.  I have a parts bike.  But will this require the case to be split and transmission completely disassembled?  I assume you can't just slide the broken primary drive out and slide the replacement in?
       

    • By Ssg
      Hello! This is my first bike with a cvt it's a 19 Outlander 850 xmr. I use the 30" cryptid tires that come with the bike during hunting season since I hunt in a louisiana swamp and I have some 27" interco reptiles during the summer trail rides. So this past hunting season I got stuck and squealed the belt do i looking at cluch kits /adjustments to help with the low end but I dont want to mess with my summer riding so I'm looking for advice 
  • Similar Tagged Content

    • By JPEDRO
      So when im ridding in high gear randomly sometimes it will go into a persay limp mode and only allows a max of 30kmph and it sounds like a rev limiter, what would cause this and how to eliminate this all togeter as in the new ones with the over ride switch. its the sound that it does in low range or reverse. i want this gone period when i get stuck in mud i cann spin tires fast enough. and while im in high gear i dont want this happening. if you need more details the easier way of getting a hold of me rather then the forum is my email [email protected] i dont have time to check back here oftern but i get my emails right away.. thanks guys
    • By Christian Brindle
      I've already posted here once about this ATV. Lots of people suggested i check the cam and after a couple months i finally got around to attacking it. I got it all apart and got the cam/rockers out. I'm almost positive they need to be replaced, they're pretty scored up and don't look too hot. Just wanted some final opinions before i drop the money on it. I'll also take feedback on the new cam i've chosen.
      Old Cam: 
      New Cam: https://www.amazon.com/hz/wishlist/ls/2GM2J05FQQPCD?ref_=wl_share
      Old Forum: 
       
       
      Thank You.
    • By johnwayne
      i have a 2000 suzuki king quad lt-f300f that i picked up as a project bike. it didnt run well when it was parked outside 5 years ago. it cranked after putting fresh gas - but would not run below half throttle, i took apart the carb, cleaned debris, and re-assembled. i suspect that the pilot needle is sheared off - it never protrudes into the throttle body through the pinhole. now to get the bike to ALMOST idle, the throttle idle adjustment knob is all the way up/in. the pilot needle is turned almost all the way in/up (if i understand correct, it should nominally be out 2 1/4 turns or so). and like i said, it will ALMOST idle. floods easily, rides rough.
      wanted to hear from those more experienced than me with suzukis - and im self-taught atv repair, so dont laugh too hard if my verbiage/part names is way off. 
      facing the driver's side of the bike [US] there are three hoses on this side of the carb. without a service manual or way of knowing what was messed up before i got it, i think i have them right: front hose as a vacuum to the petcock, middle hose as vacuum to the fuel pump, rear hose as fuel line from the fuel pump. running the bike in prime position results in flooding even while riding. with all hoses disconnected from the carb, fuel slowly drips from the vacuum line connected to the petcock.
      so just my speculation is that the diaphragm in the petcock is split, and the pilot needle is broke off - causing my inability to not quite idle and the rough ride. this suzuki is hoses and cables everywhere compared to the honda ranchers and yamaha warriors i am used to. I would like to have a plan rather than: replace everything at once.
      is my speculation on the right track, or could something else be at play? say, if the compression was non-existent, would that cause non-idling? i am all ears, look forward to the input.
    • By skymankila69
      I traded my dirt bike for a 2000 arctic cat 500 semi automatic. when i went to go pick it up the guy said it didn't get spark, so i thought it was going to be something simple like a coil. well it wasn't. first thing i did was take all the plastics off to get easy asses to every thing. so i bought a brand new battery for it seeing if it got power, it didn't. the dash wouldn't light up neither would the lights, so then i tried to see if the starter worked it didn't so i jumped the solenoid and the starter started turning over the motor. so i bought a new starter solenoid, when i installed it the electric start still wouldn't work , so i bought a new kill switch and starter switch that goes on the handle bars, when i installed it, the electric start still wouldn't work. so then i went to see if i could get spark by pull starting it, i didn't get any spark, so i bought a new spark plug, and guess what, still no spark, so then i bought a new coil for it to see if that would fix it. so i installed the new coil and guess what no spark still and still no power to the dash. so to sum it up i'm not getting any power any where to the four wheeler. so i cleaned all the leads and plugs and still nothing. so then yesterday i took the wiring apart to see if their was any frayed wires, and no their wasn't. does any one have any ideas what this could be i'm up for anything. also if any one knows how to bypass all the wiring just to get it to start i open to that to, or if someone knows where  i can get a wiring diagram.
    • By quinnkaeb
      i have recently purchased a yamaha kodiak ultramatic 400cc. it is used and sat outside for a long time. i have done a lot of work on it and got it to run sort of. when i try to start it, it will start and run for a little bit then it will die, the time it runs varies. it has a new cdi, spark plug, and stator. most of the time it wont even start it just cranks over. there was one time that it started up right away and ran perfectly but the next time i tryed it wouldnt start. before that one time every time it started and ran it had a popping sound. i cant figure out why it wont run. any help would be muchly appreciated! thanks!
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...