Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

redneckyankee

1996 Yamaha Warrior Starting Problem

Recommended Posts

ok so i had or still have a electrical problem , i have replaced all the relay's and solenoid . the only way i get the thing to start is in gear with the clutch out . if i put in neutral it does nothing ,if i put in gear and pull the clutch in it still does nothing

:aargh:

Share this post


Link to post
Share on other sites


Did you replace the neutral safety switch?

* Added manufacturer and issue to thread title.

Share this post


Link to post
Share on other sites


usually a relay goes in only one way inside a socket. But the wires going to it could be crossed. can u twist the wires together on the neutral safety switch, bypassing the switch?

Share this post


Link to post
Share on other sites

Are you saying you push it to get it started with it in gear and the clutch out or it will start with the switch as long as it's in gear with the clutch out.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Jeff Miller
      I'm trying to troubleshoot a starting issue. For a while, maybe a year sometimes I would hit the starter button and I'd hear a single loud click, but the starter wouldn't turn. Usually if I could pull the pull start or roll it in gear it would then start. (now I'm thinking that was coincidence) Now it only clicks. I tried to check what I could, battery is good, solenoid clicks strong, cleaned all connections (which were 80% clean anyway). I started thinking the starter wasn't spinning. I pulled it and it spins freely. The gear that it contacts in the engine-I can wiggle it maybe 1/16th to 1/8th inch back and forth. When I reinstall the starter I feel it jerk when I hit the button. I'm thinking maybe it's the starter clutch? It seems when there's a problem with them they usually just spin freely and don't engage at all. Is it possibly something is causing it to lock? I'm a bit lost now.
    • By Steven Urban
      First time using this forum.  Owned a Kawasaki dirt bike once, had no issues.  But I picked up this 4 wheeler at an auction.  They stated it ran, but only needed a battery.  Well I do not believe that was all true.

      Some pictures are attached.  Not sure why, but the whole air filter stuff was removed.  They had some small thing inserted as a make shift air filter.

      I purchased a battery to try this all out.  Waiting to return it and get the proper size, as it was too big for the battery box.  But here is my issue I had while the battery was connected.

      1 - The lights on the steering column did not come on.  Not sure if they work or not.

      2 - The starter solenoid seems to be bad.  I have a new one on order. 

      3 - In the pick, there is another rusted part.  Not sure what that part is or what it is used for.

      4 - What is the 12v rectifier?  square bodied part.

      So when I hooked the battery up.  Pushing the start button did nothing.  Pulling the cord to try and pull start, it turned, but would never fire.  I have put in a new spark plug as well, it looked worn out.  With electric start, I crossed over the posts on the start solenoid, it turned over, but would never fire and start.

      I have read a few other threads and it stated something about needed the neutral light on.  SOmething about a kill switch.

      Any help would be appreciated.



    • By Rigo Mena
      I have a Kawasaki bayou 220 that won’t start I don’t know if it has something to do with the electrical wires but when I put the screwdriver on both bolts of the relay it wants to crank but can’t and there’s a missing piece I think it’s another relay that has 6 wires going into it
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
  • Similar Tagged Content

    • By quadtech62
      I have a 02 Warrior i am trying to build a wiring harness i have looked in the manual and  i am confused... the pick up has 2 wires.  W/R W/G The source rotation coil has 2 wires. One is Red other is white/blue. The manual shows the  the white and blue wire connected to the w/g  right after the stator... so why is these 2 wires connected?  Does not show w/b wire at cdi 
      i have looked at many options with no luck if someone has a 2002-2004 warrior and can take a pic of the wires and location at cdi i would really appreciate it. Thanks
    • By Chase Cook
      I have a Yamaha 350 in at once to try to fire up but won't. It's getting gas fire air and it has a lot of compression but still struggles to start check the timing it's top dead center valves are good valves are adjusted everything's working but won't fire I put my hand over the carb suck in gas and it tries to but it makes a lot of black smoke. Also when I put my hand over do you carb and tried to start it there's black black nasty stuff in the gas. So I don't know if it's trying to burn too much or what it is the gas tank clean and it anything to do with the gas it's with it firing. Took the spark plug out and it's pure black. What is dried up black not nasty corroded wet looking. Need help to solve the issue
    • By Chase Cook
      I have a 2001 yamaha warrior YFM350x and started to work on it. The person who I got it from put a new top end kit in it. I already took the top end off and checked, brand new still. Had to clean the valves so it can get better compression. Put it back together and turned it over and and made good compression but also had a loud clanking noise at the bottom, put hand over carb and stopped making the noise when I turned it over. And won't start.  I know it is not the top end. Just cleaned it and valves. Need help trying to figure out what's the problem.. thinking it's the crank rod but don't know. If it is the rod can i just get a new rod for it?(would be great if so). Or does it need a hole bottom end . In need of help.
    • By Colby Calk
      I recently got a 98 warrior 350 that 'needed the carb adjusted' but the reality is it has no spark. I have a new spark plug, plug wire, ignition coil, battery, and cdi box. I checked continuity and took apart and inspected the starter/kill/light switch on the handle bar, and it all looks brand new and checked out. The key switch seems to be working properly, as when off, nothing works, but when switched on, lights and electric starter button work. It turns over fine, and as I just stated, all the lights work. I took all the plastics off and traced all the wires, and only one had a small cut in it, but it was only through the rubber sheathing, not the wire itself (the blue one coming from the stator). I cleaned some grounds, made sure both relays work, and still nothing. I pulled the stator cover and looked at the stator itself, and it looks great. No broken wires or connectors or anything. Still, no spark. I'm at a loss. Where do I go next? Any help is appreciated.
    • By Brad Lawson
      Hello all, I’m working on my sons 99 Yamaha Warrior 350. When I pulled the plastic cover off left side of engine, I can see oil leak at the seal. I pulled the bolt out and then the starter boss(I guess that’s what it’s called?) I can see that the boss doesn’t make contact with the seal. Is there a spacer of some type that slides on to the boss, to make contact with the seal? This seal is held in place with a plate with 3 screws in it. This boss slides into the bearing in the stator. I have been to parts websites and I don’t see what I’m needing. Maybe it’s just the wrong seal?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...