Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

vanmarley

how to put this front brake caliper..

Recommended Posts

i bought a new front brake caliper and honestly i need some assistance in putting this into my quad bike. and i know you guys could help me with this dilemma. your suggestions would be a great help. thank you!

front break caliper.jpg

57d773374f1bc_frontbreakcaliper.jpg.4ab66b29db696b35869a6bc675fe1e5b.jpg

Share this post


Link to post
Share on other sites


Umm we kinda need a lil more info. make, model, year, front or rear and is the old one that you are trying to replace on there still. what is your mechanical skill level? Most are held on by two bolts with locking tabs. the brake hose fitting uses the two copper washers on either side. If this has you puzzled, best bet would be to take it to a pro.

Share this post


Link to post
Share on other sites

I agree with above. If you get it on you have to bleed the brakes to get air out of the brake line. If your not sure on what your doing your better off getting it done. What is the reason for changing it out if it's because it's old and worn out! It would be better to replace both of them at the same time.

Share this post


Link to post
Share on other sites

Here's a good video on bleeding brakes..

[ame=http://www.youtube.com/watch?v=RxQkCpiQ7Y0]Brake Bleed Instructions for Motorcycles and ATVs: Bleeding - YouTube[/ame]

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Lellwyn Griffin
      I think my rear brakes are stuck.  Is these parts in the right position?  Any idea how I repair?  I have to give it more gas to go and I can't push it when it's in neutral.  


       
    • By Lellwyn Griffin
      Thinking about buy a used 07 Prairie. Any feedback or suggestions on what to look for?
       
       
      Sent from my iPhone using Tapatalk
    • By JacobSlabach
      hey so never ran into this before but i recently got a 04 honda rubicon 500.  bought it from my doctor not running and the front brakes were locked up.   cleaned the carb and it fired right up and runs great.  these model atvs have drum brakes front and rear.  not a fan.  lost all brakes on this one when i hit some water and it got inside the rear drum case.  so i ordered new shoes for the rear end no biggie.  front is more complicated.  has hydraulic drum brakes not sure who thought that was a good idea but the pistons in the drums rusted and locked up from it sitting with moisture in the drums.
      so i had a choice to make- 1. buy new brake pistons ($120 for a set of 4) or 2. order super atv's disc brake conversion kit for $250.  i HATE drum brakes so i went with the conversion kit.  it said it was easy to install with no specialty tools.  so i order it and turns out i have to press the studs out of my hubs to get the disc on.
      anyone ever done this and if so how?
    • By spock58
      I was reading another forum recently about fuel leaks and possibility of fire happening. Reminded me of an incident I had a few years ago while working at a Can Am dealership. The quad was a stolen & recovered Outlander 650 that had been tampered with. These quads have an electronic safety system, similar to their DESS system on the sleds. You cannot bypass the key switch and get spark without a computer with factory software. Anyway, I was trying to determine what was damaged since the thief had attempted to hot wire various electronic parts. I got all the extra wires removed and things looked back to stock. Pulled the spark plugs and was going to check for ignition and if the starter still worked. Well, they both worked alright and guess what - the cylinder was flooded with fuel! Instant flames with gas spraying all over...great!! I managed to use my hands to put out the fire, good thing I had on gloves (but choked they were ruined of course, haha). Seems it's possible to flood an engine with efi when you put power straight to the injectors, doh! As in much of life, you cannot take things for granted (I'd only seen carbs flood like that). And even though it had spark, the quad still needed a new ECM to run - that part alone was $1200. So lets hear your stories, crazy stuff happens every day I'm sure.
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
  • Similar Tagged Content

    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By Kevinjrr
      I have completely replaced my front brake shoes, hoses, and master cylinder. I have bled the brakes the best I could. I am still unable to build up much pressure. The wheel cylinders only push out about 1/8" when the handle is squeezed.
      What should be the typical travel on the cylinder for the brake shoe to hit the drum?
      I've used a brake bleeder, but still can't get all of the air out.
      I'm not sure what else to do.
      Any thoughts?
    • By boutselis
      I am trying to get the front brake drums off my trx250. both are stuck on.
      any tricks to getting front brake drums off?
    • By WvChillbilly
      Just curious as to why the engine brake wouldn't hold back any longer on an 08 Honda Rubicon.
      Any one feel like weighing in on this issue??
    • By vcrazy8
      I replaced the front and rear brakes on my 98 King Quad 300 today. The right front is dragging. it had plenty of clearance when I installed the drum. it turned normal until I tried to test drive it. Wheel cylinders were dry and not leaking. Also even with a dragging Right front brake they are weak. I wonder if it is something with the self adjuster and how can I get the drum back off. I just recently bought it for cheap because he got laid off of work so I don.t know any history on it. It didn't do it before but the brakes were very weak and thats why new brake shoes. old oned wereabout 60% gone. Thanks.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...