Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

BlackOpsBozo

Big Bear will start, run, turn off and won't start again

Recommended Posts

Hey guys I'm brand new to here but not to forums but here's my problem...

My girlfriends parents have a Yamaha big bear (Not sure of year or size) and they just had a guy working on it because it would turn over just wouldn't start but the guy fixed that with a new battery and spark plug but now the problem is we get the four wheeler started and drive it for a little and we go to park it and when you come to a stop it'll shut off, sometimes backfire and if you'd try to go to start it back up it won't turn over, click or anything... Like I said battery is brand new and has been checked out and it's not a faulty battery... Anybody else have any other ideas? This has been picking my brain and I cannot just put a finger on what it could be so any help is appreciated. Thanks!

Share this post


Link to post
Share on other sites


Sounds to me like the carb needs a little cleaning/inspection. Check out the float pin, it's probably fuel starved at idle and not getting enough fuel in the bowl.

Share this post


Link to post
Share on other sites

Okay that may explain the shut off and backfire but what about trying to start it back up and it doesn't crank or click? I feel like it has to be something between the battery to the starter but just no clue what all is there or what would cause that.

Share this post


Link to post
Share on other sites

The cheap check your cables hot & ground wires. If it starts everytime after it cools off my guess would be starter relay solenoid or the starter it's self.

Share this post


Link to post
Share on other sites

Okay do you know where the relay is located on it? I've also heard since they keep it in the cow barn that with the dirt in the air it can get inside the starter box and filthy up the run/kill switch and would need cleaned on the inside... Is that a possibility or ever heard of that?

Share this post


Link to post
Share on other sites


I haven't heard that, but I suppose it could be. I would check all your grounds...connections should be tight. Could be a switch, and a bad solenoid, but the fact that you don;t even get a click...how about lights? Do they come on when the electric start doesn't work?

Share this post


Link to post
Share on other sites
Oh yeah I left that part out but yeah the lights won't come on either which was leading me to something electrical between the battery and bars.

If that's the case, start with the battery or battery connections. :yes:

Share this post


Link to post
Share on other sites

Iv'e not heard of the dirt in the run/kill switch. Their seald up pretty good. I think Ajmboy is right if your not getting power to the lights could be electric. The only draw back to the lights not working that I know is on my daughters quad is the light dosen't work unless the quad is running. Iv'e never checked my kawi to see if they come on without the motor running.

Share this post


Link to post
Share on other sites

Okay well we're in a winter storm right now so I'll start tearing into it tomorrow and

I'll remove the battery and get it checked one more time and then reinstalled it myself and make sure the terminals are tight. What is the part that the power and ground cables go to about 6 inches from the battery?

Share this post


Link to post
Share on other sites


Alright so the snow finally melted and I'm checking some things today. What all grounds should I be checking out? Where they are located would be a big help too.

Share this post


Link to post
Share on other sites

Looks like a fuse holder with an extra fuse mounted on it. Your lucky day check the fuse inside there. If its blown you have a spare

Sent from my SGH-T959V using Tapatalk

Share this post


Link to post
Share on other sites

Well that's the thing... The fuse inside is good but of I grab it on both ends and put a little pressure on it I can hear a clicking noise from the rear... Not sure if its coming from the battery or there's a little box under the seat to the back above the rear taillight console with 4 different plugs (looks like a power commander or something) but when I put pressure the atv will start up right away.

Share this post


Link to post
Share on other sites


The fuse holder terminals might be corroded or the wires might be brittle. Remove the fuse and clean the terminals inside. If the fuse holder wires are brittle you should replace it with a new one

Also check to make sure there is tension on the fuse. When you put pressure on the holder you are making the connection for the electrical system. Best bet would be to splice in a blade type fuse holder of the same amperage. Any auto parts store shoild have it

Sent from my SGH-T959V using Tapatalk

Edited by marioweldinginc

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
    • By Colin Davis
      Does anybody know where I can buy a complete wiring harness for a Yamaha bear tracker. If not could someone send me a picture of the the colors of the wires coming out of the cdi plug and voltage rectifier. So I can get an idea of how I need to wire it. Also where can I find a wiring diagram for them?
    • By oxidized_black
      Clymer ATV Manual - Yamaha Raptor 700R
       
    • By Colin Davis
      I recently acquired a Yamaha bear tracker 250 that does have a wiring harness.  Does anybody have a wiring diagram for the 250s. Also if you have a pin diagram that tells be the colors of the wires going to the cdi and rectifier or just a picture of the plugs would be much appreciated. I can’t find anything on the harness online. I have all of the switches and stuff and I plan on just build a harness myself because I can’t find one to buy.



    • By Adrian Ciotinga
      Hello,
      I recently picked up an ‘07 KFX 700. All was going well, rode it about 40 miles, when it started bogging at low speeds. If I kept the revs higher, I was just fine. Also, a persistent issue since I picked it up is the fairly difficult start (but it is abnormally cold right now and the quad is jetted for the dunes at summertime).
      Regarding the complete lack of idle, I have to rev it a couple times to get it to idle after starting it, after which it’s 50/50 whether it remains idling. I don’t have low fuel, but all of this began after I rode it pretty hard and the radiator fan kicked in. Might be overheating, just wanted to hear your opinions.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...