Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Sign in to follow this  
marioweldinginc

2003 Honda 400EX LSR carrier

Recommended Posts

Quick question. Do I need to use ORings around the outside of the new carrier. The LSR carrier came preassembled but no outer orings. Use factory orings if needed?

Sent from my SGH-T959V using Tapatalk

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Similar Topics

    • By colin james
      View File 2017-2019 sportsman 450/570 with eps factory service manual
      This  is the factory service manual for the 2017-2019 factory service manual for the sportsman 450/570 with electronic power steering 
       
      Submitter colin james Submitted 09/06/2018 Category Polaris ATV  
    • By barracuda420
      Hi, I'm new to ATV/UTV's and am looking for any advice that would help to repair my 2018 Ranger 500.  I got it from an insurance auction and have never owned one before.
      It looks like it was sunk deep.  Found rocks and sand in the roof, milky oil in the air filter box, water in the fuse box, etc.
      So far, I've cleaned the air box out, vacuumed most of the rocks and sand, checked the engine, trans and diff casings for cracks/leaks.
      The battery would not charge while connected so I know there is some short somewhere...probably the wet fuse box.
       
      I plan on drying out the fuse box and all connectors with a hairdryer tomorrow, check the fuses, remove/dry out the ECM and disassemble/clean the air intake.  Then install the battery and see if i can get it to key on and see what kind of lights I get.
      Need to know what to expect with the engine/trans...
      Thanks.
       
    • By Rich1028
      Suspension Question? Shocks for 250X
      I bought the wife a 2019 honda 250X,it does not have adjustable shocks,I'm thinking of maybe getting one  as well,for her she does not notice it as much as I  do but the ride is not as good as my 1991 250X with adjustable shocks.
      So I'm looking at maybe getting new shocks if I get one for myself,I find these.
      Elka Suspension
      LEGACY SERIES FRONT & REAR KIT SHOCKS for HONDA TRX250X, All Years
      $ 999.99
      https://us.elkasuspension.com/product/legacy-series-front-rear-kit-shocks-for-honda-trx250x-all-years/
      anyone here use these shocks?and how good are they?
    • By marek porowski
      It’s kind of ATV related question as I need new trailer tires to tow my 4 wheeler. 
      Does anybody have any experience with loadstar 12” trailer tires ? 
      There is not to many choices for trailer tires here in Ontario and I was wandering if somebody can recommend me something. 
    • By warrior
      ok i have a 1987 yamaha warrior with a bad cdi i have found a good deal on one but it is a 89 not a 87 i have no problem with it not working and having to sell it but will installing and trying to fire the atv with this cdi ruin anything else ?????? i need to know sooner rather then later thank you
  • Similar Tagged Content

    • By Chayse Hill
      I have a 2003 LTZ 400 that i bought a few days ago. The quad was running fine until last night. I let my brother ride it down the street and back and i didnt notice anything etong with bike. Then my neighbors friend came over and said "can i ride it?" I said "sure" so he ripped it down the road all fine and when he got back it died right in front of us. My brother said it was dieing on him also. He also said that he wasnt using the clutch to shift. I told him he was an idiot. Im throwing that in there incase that caused a problem as well. But today i go to check it to make sure its getting fuel which it is and replaced the spark plug incase it wasnt getting spark but it is. So i started it and it was having a problem starting then i got started and was reving at idle high. So i took it around the block and it died on me a little bit down, so i try to restart it and it started so i kicked it into 1st and it kinda launched on me and started going with the clutch all the way in. Then it died right after and wasnt running right during that process and was idleing all over the place and just died and now i cant get it started it again. Before it would start without the choke or priming it. It would start real quick now i cant figure if it needs to be rejetted or something else. Air filter looks clean also. But any help would be gratelly appreciated!
    • By sloundez
      Does anyone out there know where I can get a functional pair of wheel cylinders for subject ATV? Any suggestions welcomed. Thanks
    • By Racer944
      Hi Folks;
      Has anybody on here installed a winch on a 2003 Magnum 2x4? I am using a Cycle Country adapter plate (only one I could find), but am having a bit of trouble getting it all to fit properly, and am looking for someone that may have done this install and/or may have some pics of the installation.
      Thanks!
      Eric
    • By Wonderwoman
      Hello, well back to where I was last year with this carb. Took my 250 to the mountains for the first time this year and blue smoke, too much gas again. I can't believe that this carb gives me this much trouble. Seems like the choke is stuck but the cable moves freely. Anyone else ever experience this issue? Do you think a new choke cable would maybe resolve this?http://www.quadcrazy.com/atvforum/images/smilies/arghh.gif
      OK it was the choke. Put on all new cable and plunger and she is running 100% again. So now the question is, is the carb getting worn out where the plunger needle goes in the small hole and when I use the choke the needle end doesn't get lined back up with the hole?? We'll see how it runs and now that I know what the issue is I can always pull the choke plunger out and reinstall if I start having this issue again.
    • By davidwestfall
      looking for direct shift shifting lever that properly fits my 2003 Yamaha warrior 350 and fits my foot the same as a stock 2003 Yamaha warrior 350 shifting lever fits my foot
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...