Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

newquadnewproblem

2005 Yamaha Warrior 350 Engine Cuts Out

Recommended Posts

i just got this 2005 350 warrior on a trade for some work i did. the first problem is the ignition switch was taken out. but my biggest issue that i have is that it will start up and run for maybe a min. if i m lucky then it shuts right off no matter if u keep on the throttle or not, mow when it starts i can throttle it up and keep it going for maybe a min. more but it still dies and it wont start again till it cools off or it feels like it. everything is stock and it only has about an hour worth of run time, they guy i got it from it was his kids and he drove it a little and then put it in the shed and that was it, father got it and cut out the ignition switch to get it running and couldnt, so here i am, stuck and have no clue where to start. anyone who can help and point me in the right direction would be great.thanks:confused:

Share this post


Link to post
Share on other sites


I agree, sounds like it was sitting and that carb is gummed up, float stuck maybe. The first thing to do when it stalls out is, determine if it's fuel or spark.

* Added year and re-worded issue in thread title for better searches.

Share this post


Link to post
Share on other sites

thanks guys for the help im going to try and check the spark or fuel problem first then take the carb. off and clean in out and see what happens after that. i was thinking about the carb. getting gummed from sitting dont know why i didnt follow my gut and check it.

two more questions will not having a ign. switch cause any issues with this? and

will a bad battery or anything cause this problem as well?

thanks for all the help, ill see what i can come up with and let u know,

thanks again

Share this post


Link to post
Share on other sites

to the guys that helped me thanks alot. i took the carb. apart and all the jets and ports were rusted closed and the float was stuck. after cleaning it all out and making everything shinny new i finally got her up and running and was able to ride her but im getting a hesitation when slowly taken off and i get a backfire popping out of the muffler when letting off the throttle. im thinking it needs a new plug and more run time but any idea would help. thanks again for your guys help already

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By T_bell40
      Question: Do you have to take gas tank off to get carburetor off the quad. ?? 
      It's gummed up again and needs cleaning. Put Sea foam in tank hoping it would dissolve any crud. No joy
    • By ezduzit
      So my quad will start and run pull start, i installed new battery, solenoid, ignition. the problem is
      1 the starter will try but not start. the quad. 
      2 when running i cannot shut it down with either the switch or the ignition i shut it down by allowing the fuel to run out.
      3 no lights come on headlights or brake lights
      when i turn the ignition on my neutral light works as well as the reverse indicator.
      any suggestions greatly appreciated.
    • By dave3dracing
      Hi, I'm a new member
      Just bought a used 08 350 raptor with about 5 hours on it ( very clean ). Started fine when we got it. Now after a few mods (bumper, skid plates, air filter) Now will not start unless you pull in the clutch. I've checked just about everything and also checked that there is no pinched wires. Anybody have any ideas?:bangheadc: Thanks, Dave
    • By payne
      Have an Bear Tracker 250. Dont have the manual or any literature to help with. Anyhow, starts with pull start in gear, and electric starter doesnt work. Also, neutral light doesnt come on. Where should I begin?? Need some direction on troubleshooting all this. Thanks a million.

  • Similar Tagged Content

    • By Nate Hanson
      I am a new atv owner...I bought a used atv this summer (pretty sure it is a wolverine but reg card from last owner didnt actually say that so idk for sure). It ran great for most the summer and early fall but one day I tried starting it and it turned over a while without starting and then suddenly it quit turning over at all. No click or anything.
      I charged battery and light turns on showing neutral and heatlight can go on.
      A few other things that may be pertinent: The pull start is missing, I have a fluke multimeter but not many other advanced tools (or relevant experience), there is an extra aftermarket led light attached to front but it doesnt work either... never looked into why since I didnt need it. 
      I looked for a fuse box and didnt find one.
      Please recommend some easier things to try first as I really want to avoid taking it in if I can (having one income and 4 kids can keep out extra cash, plus I want to learn). Pictures would be awesome if possible. Thanks! 
    • By Kanyon Pershing
      I have recently rebuilt my Yamaha warrior 350 engine and when I got it all back together with no “spare parts” i went to start it and realized it’s in reverse. I went to put it in drive and the shifter won’t budge, I took the linkage off and tried to use vise grips but it won’t budge at all. Any help would be greatly appreciated. I’m hoping it’s not something internal! 
    • By YamahaBB350
      I have a Yamaha Big Bear 350 and the reverse doesn’t work, it shifts from low to high easily but it won’t go back to reverse. I’m new to this stuff, so I’ll take any help. Any ideas? 
    • By Colin James Krepela
      So here's the deal people, I have an old Avenger 350 4X4 Shaft Driven ATV. They only made them in the early 80's their thought of as the first four wheelers from around back when Suzuki made one in 1982. I believe the engine on it is a Kohler as I watched this video https://www.bing.com/videos/search?q=avenger+400+atv&view=detail&mid=1E10E939019CA07770031E10E939019CA0777003&FORM=VIRE but mine is a 350. That's if its original, and it all looks original. I am wondering where I can get parts for this engine, or really what engine is it. I have no way to find the year, unless you guys know where a serial number might be. Every sticker is worn off. IF anyone has any information at all on these old wheelers it would be greatly appreciated. I specifically need the gaskets for the carb, and don't tell me I could build them please I want to restore it as perfectly as I can. I can take pictures of the wheeler/carb if it'll help. Let me know.
    • By oleskool
      Has new top end, piston, rings, valves, etc. great compression, good spark, plenty of fuel. Valves have been set. timing has been tripled checked. Can not get it to start. any ideas suggestions on anything I am missing. Also if anyone has the service manual it would be greatly appreciated.

      Thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...