Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

redneckinker79

2000 Yamaha Big Bear 400 4x4 - Need Help ???

Recommended Posts

i took off the pull starter and looked for the timing plug so i can adjust my vales and there is no spot like that what do i do its a semi auto 5spd full time 4x4 :confused:

Share this post


Link to post
Share on other sites


ok i just checked my air box cover and it says engine family is YYMXX.387GCB AND NOT TO MENTION I FOUND SOME OIL IN THE BOX AS WELL IF ANYONE HAS ANY IDEAS PLEASE LET ME KNOW THANKS STILL CONFUSED

Share this post


Link to post
Share on other sites

you will find the vin usually on the frame by the motor on the left side (drivers door). you can decode it here :

Yamaha VIN Decoder @ Motoverse.com

a little oil is normal (no more than a couple teaspoons) if you have more, it usually means you overfilled with oil, you have a blocked crankcase vent line or a plugged exhaust. if your rings are bad, the pressure in the combustion chamber will create pressure in the crankcase and force oil up through the vent lines.

Share this post


Link to post
Share on other sites

yeah its about a couple of teaspoons so im figureing the rings are worn out as well but it def made a huge difference in performance im going to get a feeler gage today to set it right thanks again

Share this post


Link to post
Share on other sites


well i blew it up i guess changed the oil and then all it did was smoke like crazy lol rings and piston are shot after it stopped smoking ran great for two days and then just died so tore it down and looking to get a piston and ring set dealer has one for about $210

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tiffany Rowland
      I recently purchased an 07 Honda sportrax and when I was checking the spark plug I saw the boot was ripped nearly in half. When I removed the plug it was blackened and covered in oil. How can I thoroughly clean the plug hole and remove any debris that is in there? Is there a small tube like vacuum or something of the sort made for stuff like this? The machine my dentist has would be perfect, maybe they do rentals! 😁

    • By YamahaGrizzly
      So my Yamaha grizzly 700 wasn't going into reverse for some reason but Jon and George figured it out on what to do to fix that problem for me. Jon Talks about how he was able to fix that problem my Yamaha Grizzly was having with the reverse.
      On a side note we are so close to 1k subs! hell ya!
    • By Tiffany Rowland
      I recently purchased an 07 Honda sportrax and when I was checking the spark plug I saw the boot was ripped nearly in half. When I removed the plug it was blackened and covered in oil. How can I thoroughly clean the plug hole and remove any debris that is in there? Is there a small tube like vacuum or something of the sort made for stuff like this? The machine my dentist has would be perfect, maybe they do rentals! 😁
    • By Cj Winds
      I have a 2000 Polaris Xplorer with the 250 two stroke motor
      It does not want to start with the electric start, the motor cranks fast, the battery is good, and there is good spark when cranking. The engine starts perfect when using the pull cord, it even starts if I pull the cord slowly and starts with one pull. The engine idles smoothly once started. My wife says she needs the electric start to work.
       
    • By Monika Novakov
      1988 Kawasaki 220 Bayou trying to remove generator/ starter 1way clutch cover to be able to replace 1way clutch. All bolts are removed case cover is dripping what oil that remains...but I can't get the cover to come off..what am I missing? Thx in advance.
  • Similar Tagged Content

    • By Christian Brindle
      I've already posted here once about this ATV. Lots of people suggested i check the cam and after a couple months i finally got around to attacking it. I got it all apart and got the cam/rockers out. I'm almost positive they need to be replaced, they're pretty scored up and don't look too hot. Just wanted some final opinions before i drop the money on it. I'll also take feedback on the new cam i've chosen.
      Old Cam: 
      New Cam: https://www.amazon.com/hz/wishlist/ls/2GM2J05FQQPCD?ref_=wl_share
      Old Forum: 
       
       
      Thank You.
    • By johnwayne
      i have a 2000 suzuki king quad lt-f300f that i picked up as a project bike. it didnt run well when it was parked outside 5 years ago. it cranked after putting fresh gas - but would not run below half throttle, i took apart the carb, cleaned debris, and re-assembled. i suspect that the pilot needle is sheared off - it never protrudes into the throttle body through the pinhole. now to get the bike to ALMOST idle, the throttle idle adjustment knob is all the way up/in. the pilot needle is turned almost all the way in/up (if i understand correct, it should nominally be out 2 1/4 turns or so). and like i said, it will ALMOST idle. floods easily, rides rough.
      wanted to hear from those more experienced than me with suzukis - and im self-taught atv repair, so dont laugh too hard if my verbiage/part names is way off. 
      facing the driver's side of the bike [US] there are three hoses on this side of the carb. without a service manual or way of knowing what was messed up before i got it, i think i have them right: front hose as a vacuum to the petcock, middle hose as vacuum to the fuel pump, rear hose as fuel line from the fuel pump. running the bike in prime position results in flooding even while riding. with all hoses disconnected from the carb, fuel slowly drips from the vacuum line connected to the petcock.
      so just my speculation is that the diaphragm in the petcock is split, and the pilot needle is broke off - causing my inability to not quite idle and the rough ride. this suzuki is hoses and cables everywhere compared to the honda ranchers and yamaha warriors i am used to. I would like to have a plan rather than: replace everything at once.
      is my speculation on the right track, or could something else be at play? say, if the compression was non-existent, would that cause non-idling? i am all ears, look forward to the input.
    • By skymankila69
      I traded my dirt bike for a 2000 arctic cat 500 semi automatic. when i went to go pick it up the guy said it didn't get spark, so i thought it was going to be something simple like a coil. well it wasn't. first thing i did was take all the plastics off to get easy asses to every thing. so i bought a brand new battery for it seeing if it got power, it didn't. the dash wouldn't light up neither would the lights, so then i tried to see if the starter worked it didn't so i jumped the solenoid and the starter started turning over the motor. so i bought a new starter solenoid, when i installed it the electric start still wouldn't work , so i bought a new kill switch and starter switch that goes on the handle bars, when i installed it, the electric start still wouldn't work. so then i went to see if i could get spark by pull starting it, i didn't get any spark, so i bought a new spark plug, and guess what, still no spark, so then i bought a new coil for it to see if that would fix it. so i installed the new coil and guess what no spark still and still no power to the dash. so to sum it up i'm not getting any power any where to the four wheeler. so i cleaned all the leads and plugs and still nothing. so then yesterday i took the wiring apart to see if their was any frayed wires, and no their wasn't. does any one have any ideas what this could be i'm up for anything. also if any one knows how to bypass all the wiring just to get it to start i open to that to, or if someone knows where  i can get a wiring diagram.
    • By quinnkaeb
      i have recently purchased a yamaha kodiak ultramatic 400cc. it is used and sat outside for a long time. i have done a lot of work on it and got it to run sort of. when i try to start it, it will start and run for a little bit then it will die, the time it runs varies. it has a new cdi, spark plug, and stator. most of the time it wont even start it just cranks over. there was one time that it started up right away and ran perfectly but the next time i tryed it wouldnt start. before that one time every time it started and ran it had a popping sound. i cant figure out why it wont run. any help would be muchly appreciated! thanks!
    • By bradleyheathhays
      I'm going to check the valve clearance on my 2011 Grizz 700 for the first time and I'm also wanting to check the timing, but I'm not sure how to do it. What tool (light gun?) do I need for this job and how is it done?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...