Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Jpvip1

1993 Kawasaki Bayou 300 - Won't Start

Recommended Posts

Having trouble with a bayou 94 Kawasaki 300 that's been sat up for a year. Installed the honda carberator cleaned tank put new gas . After all of this it ran with a rough idle but it did run I ran it for about 45 minutes. Next day it will not start any suggestions?

Edited by Jpvip1
Fourgot items

Share this post


Link to post
Share on other sites


Hi, you were correct, I installed a new plug and it fired up and now it does run. My next problem is the idle, it has a rough idle it is up and down, I tried adjusting the air screw both in and out and it increases and decreases the idle a little but it is not a smooth run it still goes up and down, it's just a rough idle. Ivan ride it and it runs if ebut when I stop the idle goes back rough running, after idling a few mi utes I have to use the throttle to keep it running it wants to stop. Any suggestions

Share this post


Link to post
Share on other sites

there is an air/fuel mix screw, mine is on or near the underneath of the carb, and an idle screw, usually quite big with a spring. alot of people will think it's either or a mix/fuel or idle screw, i know i did until i talked to cheriah here. that is all i can think of, usually the idle screw is suggested to be turned in all the way tight, then 1 1/2 to 2 1/2 turns out, then you adjust the fuel/air mix screw ....

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tiffany Rowland
      I am working on a Honda sportrax I just got my daughter for get birthday and the reverse and neutral light are not working. When I traced the wire down I saw that it wasn't plugged in but I don't see where it is supposed to connect. Does any one have a general idea of where I should look?

    • By Gary Skriba
      just got a 99 Kawasaki bayou replace the coil because the spark was very weak still have the same issue before it would start after a while that it would start everyday as long as you started it every day but if you let it set you play hell starting it looking for information on what could possibly be wrong maybe the CDI box not sure any help would greatly be appreciated thank you
    • By Christine Kiffer-Meany
      Hey everyone...does anyone know if tie rod sets for a Honda 250 will fit a 125? My son just snapped the tie rod end clear off. We have a 1987 Honda fourtrax 125. Just want to make sure before I order the set off eBay. Thanks
    • By Joe Dickerson
      I decided to replace the rings and piston on this machine because it looked like the plug was being fouled by oil. When I removed the right side of engine to inspect the clutch pack, I found 2 small round pieces with tiny expansion rings in the bottom cover. It looks like "clutch pawls" according to the illustration, but Id like to be sure. I saw that there are 4 of these in the new gasket set.
      Can someone help me here?
      I thank you in advance
      Joe
       
       

  • Similar Tagged Content

    • By Guythis448
      Looking for help on wiring up stock wiring harness specifically for a '88 Honda TRX 300 
      If anyone could drop a link or send me a PM it would be much appreciated 
    • By pizzaman_288
      How hard is it to change the outer seals on the rear differential mine are leaking fluid and I have no idea on how to change them out any help would be great thanks
    • By mmgood
      Just bought a 1987 bayou 185 frame and body great shape but have to rebuild motor does any one here have a manual for a 1987 kawasaki bayou 185 ? if you you do please let me know.
    • By katasha2
      I took apart the carburator to clean out and I can't remember exactly where the springs that are inside the float are supposed to go I've tried to look up schematics but I think I am missing a spring maybe need helpt:confused::confused:
    • By Ironfist104
      My wolverine has a new carb kit, new battery cranks over and over take it to the point of killing the battery to start sometime.... but it I give a tug on the start rope while I'm cranking it with the starter it fires right up.... any advice?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...