Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Daryl Mann
Hey new to the page
having an issue with my carb slider jamming ect just replaced the carb with a good pre owned unit and seem to be having a similar issue
is there a home fix for this as a posed to buying yet another carb as the quads my daily transport and stuck without it
thanks for looking any help great full can also forward video of the problem I’m having if needed
By wendi loden
I replaced the fuel pump filter and it ran great for a week or so. Then while driving across the yard in 3rd gear it shut off and hasn't started since. It has fire and its getting fuel, all fuses are good, battery fully charged. The fuel pump relay seems to be warmer than it should be when spinning it over. Any help is appreciated!
Unfortunately I didn't notice some of the rust hitting the undercarriage of my 2004 Yamaha Grizzly 660, but saw it the other day when I was doing some maintenance, oil change, air filter, spark plug, etc. The left side footrest broke and that's causing the plastic to hit the front wheel. It broke right at the welds from too much rust. Looks to me like what I need is (looked this up on yamahapartshouse.com):
YAMAHA FOOTREST BOARD 5KM-27481-10 Left side (broken)
YAMAHA FOOTREST BOARD 5KM-27488-10-00 Right side (rusted and will probably break eventually)
Does anyone have a less expensive source? I did see on ebay a couple of listings but it still comes out to @ $50 each,
I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
Here's some of the tools you will need...
1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.
2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.
3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.
4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.
4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.
5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!
Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.
7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.
6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
The whole process only takes about 15-20 min.
By Shawn Hurt
I have a 2013 KQ I bought it new but rolled it a few years ago. I have replaced the left lower A-arm and left tie rod, the steering is still a little sketchy as I just eye balled the alignment. But the major issue is the left front tire cambers out at the top and has wore the tire bald. Tires have about 2000 miles on them but other 3 are half tread and left front is a slick.. I can not see anything else bent and don't know what to do..
Similar Tagged Content
I've been looking into buying a house and my rock buggy that I have been building for 5 years had to go... I sold most of the parts so I decided it was time for a new toy..
I found a 2008 RZR, its got ITP wheels/ ITP Terracross tires, front/rear bumpers and top. I threw some 4 point harnesses in it already and have a set of suspension seats left from my buggy that im going to try to put in it... I just ordered a UMP filter setup to do away with the crappy stock filter box. HID lights, Optima battery and exhaust are in the works for next month... Long travel and a few other thing are in the plans in the near future too...
A small zoo in West Virginia obtained a very rare species of gorilla.
Within a few weeks the gorilla, a female, became very difficult to handle. Upon examination, the veterinarian determined the problem. The gorilla was in heat. To make matters worse, there was no male gorilla available.
Thinking about their problem, the Zoo Keeper thought of Buckbilly, a redneck part-time worker responsible for cleaning the animal cages. Buckbilly, like most rednecks, had little sense but possessed ample ability to satisfy a female of any species.
The Zoo Keeper thought they might have a solution. Buckbilly was approached with a proposition. Would he be willing to mate with the gorilla for $500.00?
Buckbilly showed some interest but said he would have to think the matter over carefully. The following day, he announced that he would accept their offer, but only under five conditions:
"First", Buckbilly said, "I ain't gonna kiss her on the lips." The Keeper quickly agreed to this condition.
"Second" he said, "She must wear a 'Dale Earnhardt Forever' T-Shirt."
The keeper again readily agreed to this condition.
"Third", he said, "you can't never tell no one about this." The keeper again readily agreed to this condition.
"Fourth", Buckbilly said, "I want all the children raised Southern Baptist." Once again it was agreed.
"And last," Buckbilly said, "I'll need another week to come up with the $500.00".
Recently Browsing 0 members
No registered users viewing this page.