Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

foreman

2004 Suzuki Ozark 250 - Idle Problem

Recommended Posts

I HAVE A 2004 OZARK 250. I pulled it out after winter and now it is not running right. It starts up fine idles fine and runs fine up to half throttle. As soon as u hit half throttle it just starts dieing(spitting and sputtering). I put some seafoam in the tank and it kinda cleared it up a little(when in nuetral) but as soon as u put it in gear and hit half throttle it runs bad again. any info helpfull.

Share this post


Link to post
Share on other sites


take the carb off and clean the whole thing...and use fresh gas....check the tank screen for obstructions and check your fuel filter also..all of them can get gunky from sitting...1/4 --3/4 throttle is the jet needle and needle jet, the main jet holder may be gunky....good luck:wink:

Edited by cheriah

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Hondasher
      I have a 2004 Polaris Trail Boss 330 and I want to eventually fix it up if possible, but the thing is the transmission or Gearbox that allows you to shift into forward and reverse and such isn't connect to the engine at all, it isn't even bolted into the frame. Anyways the Secondary Driven clutch is missing. The ignition was busted so I switched it out and tried to hook up power to it and the lights wouldn't light up and it wouldn't try to let me start it with the electric starter. 
       
      So I bridged the connectors on the starter solenoid and it cranks the motor. I was wondering if anyone knew why the dash lights don't work or any of the buttons. I did find a cable disconnected I have a picture of maybe someone can tell me what it's supposed to be connected to. It has 3 wires going to the connect Green Purple Red. I'll enclose a picture of it and where it is connected on the wiring harness. 
       


    • By Randel1
      Hello, 
      I have a 2004 Yamaha Bear Tracker in the shop for repair. I have the service manual but it doesn't have all the information I need to fix the problem. I need to know the voltage output of the stator charge coil and pulse or trigger coil at cranking speed. The wiring diagram color code doesn't seem to match and that is compounded by the fact that the wiring harness CDI connector is missing so I have 7 wires that need to be connected to the CDI. I can not find a circuit diagram of the CDI which tells me where the pulse/trigger coil connects or the charge coil connects. The other 3 wires (black ground, orange ignition coil, and r/b ignition kill sw) also need to be connected. The CDI has a single 8 pin connector and has a P/N 4XE-00 F8T19871 -1122 number on it and I believe it to be OEM. However I think the Stator and pulse coil are aftermarket items. I have resistance tested everything and it all seems to be in spec. but I don't want to miss wire anything and cause damage. Any help would be greatly appreciated. 
    • By Colin Davis
      Does anybody know where I can buy a complete wiring harness for a Yamaha bear tracker. If not could someone send me a picture of the the colors of the wires coming out of the cdi plug and voltage rectifier. So I can get an idea of how I need to wire it. Also where can I find a wiring diagram for them?
    • By Roy Anderson
      I have a 2002 Suzuki LT-F500F, and am a first time atv  owner. I rode two wheel bikes for many years, and now, two months in to being a new at owner, am just not enamored with the thumb throttle, and I’m wondering if anyone has tried a conversion to a typical twist grip throttle as found on all motorcycles? If so, how do you like it?
  • Similar Tagged Content

    • By Trenton
      Hello. I am a new member as of today. I had a quick question to ask. I recently was driving mt HONDA RANCHER 2004 GPSscape 400 and my display stopped working. I was driving the atv and all of a sudden the speedometer and the service lights went out. Also the lights stopped working. I am still able to shift gears, change from 2wd to 4wd, and can still select if I want EPS or Auto. I have checked my fuse box and have changed a few of them around. It did not change anything. I was wondering if anyone had any idea of what had happend. Thank you for your time- Trenton 
    • By LTZ-Zach
      So i was riding the other day and my quad randomly shut off. It started back up and ran completely fine for a little while and then it started idling terribly.
      I cleaned the carb and changed all the jets and everything except the float due to the rebuild kit not coming with one and it actually runs worse then it did before.
      It will run and idle decent now but when I give it gas it dies.
      Does anybody know what could be wrong?
      I also changed the spark plug and air filter along with the oil and oil filter.
       
    • By Jers
      I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
    • By Kyboy
      Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...