Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
So just as a general FYI, it might be good to check replacement parts before installing. If possible, check clearances with a micrometer before going through the trouble of assembly. I say this as I bought a new driveshaft yoke for a Kodiak because the ujoint dropped a cap and got the yoke in a bind...blowing the yoke and middle drive gear to shreds. So I replaced the middle drive gear and bought a new yoke and ujoint kit from Caltric. Caltric is usually pretty solid replacement parts. The new yoke however was a good 4mm too narrow for inside lock ujoint caps. Disappointing since it came as a kit from Caltric.
Ended up taking an angle grinder to the new yoke and thinning material off to get it to the needed 41.25mm opening size. Sucks having to disassemble everything again and start over but my fault for trusting replacement parts. Nearly 40 years of turning wrenches and I made a rookie mistake.
I recently read an article about restoring or at least improving the looks of faded and discolored plastic body parts. In the article it suggested using a 50/50 mixture of boiled linseed oil and paint thinner. You mix it up and apply it with a brush or rag to rub it in and remove the oxidation. I curious to find out if anyone has had experience with doing this and what was their short/long term results of doing so. I would hate to try it and find out that a few weeks/months down the road my plastic body parts self destruct.
Damn, it took 30 years of driving to cause my first accident, and on Friday the damn 13th. Did a low speed rear end into the back of a lifted truck and got into it's trailer receiver. The only place it made contact with was at the very front center of the hood close to where it latches. Unfortunately the impact was enough that there's a longitudinal hump in the middle of the hood now, bowed 6 inches on each side above the quarter panels, which weren't involved at all thank God. Both my headlights are cracked at the top, but not because they got hit; I think it was because the hood and it's latch was pushed back during the collision possibly deforming the support structure, causing the to separate. The hood is lifted up about 3 inches above each headlight and when looking in at the support material just behind each headlight, one side shows cracks and the other cracks and about a 1/2 gap in the material. Can't tell but it may resemble fiberglass, not really sure? My best guess is that the whole front bumper is gonna have to come off and that entire front support piece be replaced. Any advice on how hard this can be? I do a lot of my own work but I really don't want to be getting into this especially with the weather getting so bad now.
When I go junkyard shopping for parts, what year Tauruses are compatible with my '02?
By My kiwi shed
Currently have a 2004 King quad 300 4wd.
There's a few parts I need to get 4wd working again and also have a crack in the engine crankcase(big trucking rock).
Replacement engines are horribly expensive so looking for a half decent site to buy parts /kits that also have detailed diagrams and part numbers.
Going to disassemble weld crack and give the engine a freshen up.
Any recommendations please
Similar Tagged Content
By Resurgence Small Engine Inc.
Used ATV parts available from Resurgence Small Engine Inc.
All parts have been identified by manufacturer's part number, photographed, and listed on our website.
Our used OEM parts are available for up to 60% off dealership prices. This way you can maintain your machine with well-made OEM parts at a more affordable price!
Compatibility can be confusing, but we’ve simplified it for you. Browse our current parts inventory by type, make, year, & model or search by OEM part number.
We make the logistics easy with our Free Shipping Promotion on US orders over $100!
Visit our website to view our current inventory:
Parts are located at Resurgence Small Engine Inc. in Wasilla, AK. Free local pick-up is available and our website is configured for domestic US shipping. For international orders, please contact us.
More parts & models to be listed continuously! As of August 2018, parts are available for the following ATV models:
Parts are listed for many models, currently including:
Kawasaki 2003 KFX400 Polaris 2010 Ranger 500 4x4 HO EFI Suzuki Quadrunner 250 LT4WD 250 LTF250 500 LTF500F King Quad 250 LTF4WDX 300 LTF4WDX 450 Quadmaster 500 LTA500F 4x4 Eiger 400 2x4 400 4x4 Ozark 250 LT250 Vinson 500 LTA50F Yamaha Banshee 350 Big Bear 350 Raptor 350 Warrior 350 Wolverine 350 More parts & models will be added continuously!
Resurgence Small Engine Inc.
Hello guys! New to the forum, and fairly new to ATVs. I've driven them, but never owned one. Now I do own one. Just picked it up today. It's a 1999 Yamaha Big Bear 350. It's been through some stuff. The guy I got it from told me the previous owner removed the front diff because he didn't want to replace the half shaft. So it's 2wd, even though it's supposed to be 4x4. Lovely. I can deal with that for now.
More importantly, I need to get it running. The carb needs to be rebuilt. The guy I got it from said he sprayed it all out and it still didn't work. I'm concerned he might have damaged it or not put all the parts back. I was looking at a replacement carb, and the OEM parts is $600. I'd rather not spend $600 if there are any other options. I have seen carbs on Amazon and eBay that are in the $40 - $100 range that say they fit. Anyone have experience with these? I'm going to get a rebuild kit for the current carb just to make sure that won't fix it.
Thats the first thing with it. Secondly, it was completely rewired. I need to find a original wiring diagram so I can put it back how it was, with a key and all. Currently it's wired with just a rocker switch. Any sources for a service manual that would include wiring diagrams?
Thirdly, is the Big Bear 350 a good atv? I picked it up for $700. It does start and run when you spray starting fluid into the air intake, so I am not concerned about the engine being bad. I plan to use it for the farm, running around and carrying things with it like minerals and feed and such. Not really for mudding and things like that. How good is the 99 350?
I am certain I will have more questions as I examine it more, but that's all for now. Thanks in advance for the assistance!
Recently Browsing 0 members
No registered users viewing this page.