Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

paintapig

polaris phoniex bucking

Recommended Posts



That has happened to me twice with my Trailblazer. Firts time it was a blocked fuel filter and the second time the belt was slipping. The fuel filter had a hesitation or sputter and jumped as the fuel got through. The belt just made it jump as it slipped and grabbed.

Share this post


Link to post
Share on other sites
when i give my quad full gas it bucks and jumps alittle any idea where i can start digging?

Define bucks and jumps ?:huh:

Share this post


Link to post
Share on other sites

did the fuel line and belt help?? it just kinda seems like it loses power and it jumps enough that the whole machine feels like the rear end it comeing off the ground. but if i kinda father its alittle better

Share this post


Link to post
Share on other sites

From what you a describing it sounds like a fuel issue. Either the filter or the carb needs to be cleaned or adjusted. Also check the plug to see what kind of condition that is in. The plug will usually show if you have a lean or rich fuel problem.

Share this post


Link to post
Share on other sites


It could be fuel, but my gut says it's a belt/clutch issue. When was the last time you checked the belt? How many miles are on the belt? ------I only suggest the belt because my sled acted the same way. 04 Polaris 700.....that sucker would rip-it off the line then lag off and vibrate like crazy, like it was loosing power from the motor. I did'nt check the belt until it exploded during our usual "field races".:realmad: Glad I had a spare! When I changed tto the spare I saw how dirty the whole area was with rubber debris. New belt and cleanded evreything up and it screamed again. I'd be checking the belt and sheeves on the clutch and secondary. Make sure the belt is in good shape & within specs & that your sheeves are clean.

Share this post


Link to post
Share on other sites

ok thanks everyone. i will try changeing the belt first. hopefully thats all it is. i already cleaned the carb like 3 times. so i think its cleaned. ha.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By JacobSlabach
      I have a gentleman that asked me to service his bayou for him.  I have always wondered what oil should be used in atv engines?  Pros?  Cons?  What weight should be used in what type of weather?  Is there one kind that I could bulk buy and safely used in any quad I worked on or owned?  What about performance?  Engine Life?  This has always been a 🤔🤔🤔 area for me with quads as far as why you would use one type of oil over another....
      Thanks!
    • By Steven Urban
      First time using this forum.  Owned a Kawasaki dirt bike once, had no issues.  But I picked up this 4 wheeler at an auction.  They stated it ran, but only needed a battery.  Well I do not believe that was all true.

      Some pictures are attached.  Not sure why, but the whole air filter stuff was removed.  They had some small thing inserted as a make shift air filter.

      I purchased a battery to try this all out.  Waiting to return it and get the proper size, as it was too big for the battery box.  But here is my issue I had while the battery was connected.

      1 - The lights on the steering column did not come on.  Not sure if they work or not.

      2 - The starter solenoid seems to be bad.  I have a new one on order. 

      3 - In the pick, there is another rusted part.  Not sure what that part is or what it is used for.

      4 - What is the 12v rectifier?  square bodied part.

      So when I hooked the battery up.  Pushing the start button did nothing.  Pulling the cord to try and pull start, it turned, but would never fire.  I have put in a new spark plug as well, it looked worn out.  With electric start, I crossed over the posts on the start solenoid, it turned over, but would never fire and start.

      I have read a few other threads and it stated something about needed the neutral light on.  SOmething about a kill switch.

      Any help would be appreciated.



    • By JacobSlabach
      i know this isnt an atv but same type of thing.  I have a riding mower im fixing and selling for my aunt and it has a dead battery.  i jumped it off my atv and when i turn the key nothing at all happens.  i tried jumping the relay still nothing.  this is with the seat down.  you wouldnt think this mower would have issues as its a top-of-the-line brand and almost brand new (aunt found it for a good price, still got tits on tires, just sat for a couple months in a mechanic shop
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
  • Similar Tagged Content

    • By Beb1041
      Looking for a download of a manual
    • By warkcol
      I am having an issue where it sounds like the gears are slipping if I hit the throttle really hard and also after letting off when the engine brake is applied. Also, the drive train that goes to the front also rides again the gear shift box. I will attach pictures and a video here shortly.
      Thanks in advance!
      [ame]
      [/ame]https://postimg.org/image/cdlu6fza9/
    • By Weldingrod47
      Trying to change front wheel bearings. I removed the cotter pin and castle nut. Hub won't budge. Is there an additional retaining clip? Seems to be one of those push on type that barbs on the thread of the spindle. How do I remove it?
    • By buzzar56
      I am looking for a free repair manual for a 2003 Polaris sportsman 500 ho atv. all the posts on here lead me noplace
      thanks fred.
    • By RoxanneRoseReid
      Need a polaris manual for a 1994 2 stroke 2/4x4 quad free. can you please post a link I can click on Thank you. Roxanne
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...