Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

DC310r

tri z 250 wont rev past 3/4 throttle

Recommended Posts

i have a 86 tri z 250 Ever since i got it it hasnt ran quite rite,In lower rpm runs ok and free revs great but anything past 3/4 it acts like it has a rev limiter?Its all stock with a pipe,I thought it mite be carb so a i put one my 38mm carbs on and it still does the same thing just gets there faster know lol.This machine should be right up there with my 250"s just not running a maximum.please help.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Buell
      Hey guys, figure you guys would have some helpful direction or answers.
      So, 05 Sportsman 700 carb, new carb, fuel pump, new plugs, new air filter, new everything I can think of that is usually the running issues. Starts up fine, seems to run fine, but if under load, two people, or even one person, up a hill, or pulling a drag chain for the driveway, it starts to cut out and sputters and loses all power, until I back off on the throttle and just barely try to let itself catch itself and then I can take off again.
      I am going crazy trying to figure this thing out. Other than that, the quad runs great. Parents bought bran new, just used around the property, 5000 miles on it. Any ideas???
    • By Ellery Zandt
      Does anyone have a redcat 250 or falcon 250cc that they can share where the two vacuum lines on the carburetor that you run antifreeze through I honestly have no idea where the lines are suppose to go to circulate the antifreeze. 
       
      Any help is greatly appreciated. 
       
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By PKR
      I rebuilt the carb on a 1989 350 Big Bear. This is a Gen 1 carb ( 2 cables running to throttle).
      Quad starts and runs but I have fuel leaking from the air intake.
      Is the float set to high / low?
      Does the needle for the main jet need adjusting? I have it on the center groove ( 2 groves above and 2 groves below).
      All jets are new, float and needle and seat are new.
       
      Thanks for your help
      PKR
  • Similar Tagged Content

    • By Ellery Zandt
      Does anyone have a redcat 250 or falcon 250cc that they can share where the two vacuum lines on the carburetor that you run antifreeze through I honestly have no idea where the lines are suppose to go to circulate the antifreeze. 
       
      Any help is greatly appreciated. 
       
    • By BosoxBruce
      Recently I noticed gas leaking from under the gas tank on my 2005 250 2x4. As I looked closer it appears to be leaking from the shut off valve under the tank. It's the valve with the handle that can be turned to open, close or reserve. Can this part be replaced? Thank you.
    • By Derick Joel Smith Trimmings
      Buying a Baja 250 tomorrow for 600 bucks, needs nothing but a wheel bearing, i already know Baja is an off brand crappier. Manufacturer, but does anyone have any tips or knowledge of these bikes? 
    • By fatfarmboy
      Just bought (Tue. evening) an '89 Suzuki 250 4wd that has been sitting out the last 5 yrs. It's complete, including the shift knobs, battery cover, and headlights. It has the optional cooling fan on it (probly stuck - didn't check), and the engine isn't locked up. Plastic looks good and isnt cracked. Racks aren't bent up. Shift lever works, the foot brake moves (needs oil - have to pull it up by hand), and there's black oil and no water in the engine sight glass. Guy was asking $125 and gladly took $100 for it. Anxious to get started on bringing it back to life. Been wanting one of these for years. As soon as I can get to it (working on a junky "Jackel" right now - Chinese Yamaha Timberwolf). I'm going to pull the tank off it and clean it, clean & possibly rebuild carb, put in new plug, and a battery, then see what happens. If nothing, will keep going until it runs. Feel free to respond if you want to, I'm mainly just excited and wanted to tell somebody. 
    • By Flanstone
      I just bought two 1985 TRX250's from my father-in-law. One runs great, the other not so much. The one is having issues with the shifter. The shifter seems to be resting lower than normal. When I press the shifter downward, it just pops back up. Any thougjts as to what the issue might be?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...