Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

quintain

1990 Yamaha Big Bear 350 - Throttle Cables

Recommended Posts

Hi, (Big Bear 350 4x4 1990 +- year, I am still looking for the VIN).

Quad starts and runs and has 2 cables coming out of the throttle cable assembly one goes to the carb the other is not connected.

Where should the unconnected cable be connected to ???

I have a service manual but can only find talk of "Throttle valve cable" and "Piston valve cable" I cannot see where the "piston valve cable connects.

Any help especially with pictures would be good.

Share this post


Link to post
Share on other sites


Hi There,

New here but was just cleaning the carb on my 1990 Big Bear a few weekends ago. If you cant readily see exactly where that second cable goes I suspect your machine might have a newer carb on it.

On my carb, there are 2 brass "ports" for cables. One on the side for the throttle. One on the top for the piston. One actuates the butterfly, one actuated the recangle-ish piston within the carb body.

Hope this helps!

Share this post


Link to post
Share on other sites

here's what my '91 looks like with the gas tank and seat removed ....

IMG235_zpsa6f7bc9b.jpg

IMG236_zpsd1b03f1f.jpg

both of these cables join in a junction box and a single cable goes back to the throttle lever ...

Share this post


Link to post
Share on other sites

Thanks to you both.

My carb does not have the top connector, the one with the 3 screws holding it down.

My carb looks like your picture but the top piece has no opening.

Any thoughts ??

I can send a pic (later) if it would help.

Share this post


Link to post
Share on other sites


I'll strip it over the weekend end and see what is under the top !!!

But what should my missing connection do ??

Share this post


Link to post
Share on other sites

Yeah, your carb is not original but your cables are.

The second cable manually actuates the piston inside the carb body. The kind you have is actuated by vacuum.

search youtube for " yamaha big bear" and there are a couple videos on carb cleaning that shows your style carb.

I believe your carb is just a later model. Not sure if one is better that the other or not but should function just fine.

Edited by Getch

Share this post


Link to post
Share on other sites

Thanks Getch

It could be that the bike is a bit newer than I thought.

I cannot see that anyone would have changed the carb for a newer one.

I have watched youtube on a number of carb cleans and when time permits I will strip it and see whats happening.

I still cannot find the VIN and I am looking in the correct area i.e. frame below or in front of gear shift, I can almost (I think) see some sort of marking on the frame behind the shift.

The bike has had a hard farming life and is banged about and surface rusted. But I hope to eventually get the VIN.

At this moment I am working, when time permits, on the brakes and have just discovered that the bleed screw on the nearside front is damaged so I need to fully strip that down.

Thank you for your interest.

Share this post


Link to post
Share on other sites

I still cannot find the VIN and I am looking in the correct area i.e. frame below or in front of gear shift, I can almost (I think) see some sort of marking on the frame behind the shift.

The bike has had a hard farming life and is banged about and surface rusted. But I hope to eventually get the VIN.

check where the handlebars go into the frame too ....

Share this post


Link to post
Share on other sites


Will do.

Email hiccup for the last hour or so, my service provider had a hiccup.

Some messages may have been returned as undeliverable.

All is now good and safe.

Regards

quintain

Share this post


Link to post
Share on other sites

Thanks o_b

I believe I downloaded your service manual which I am embarrassed to say I did not thank you for; but belatedly I do so now.

As a new user of the or indeed any quad the pic at 4.1 in the service manual did not fully make me aware of the 2nd throttle cable position.

I can see it now including the description of "Piston Valve Cable" on id #8 on the page.

I will be most interested to see what is discovered when I open up the carb. Either a bad alteration or a vacuum operated carb.

Thanks again.

Share this post


Link to post
Share on other sites

Just for update

These pics of my carb may help someone else.

It is a single throttle cable that operates all that is needed BUT it has been fitted with a twin cable from the throttle assembly with one cable not connected.

The pics show the operating connection with some red tape on it.

Thanks again for help and advice.

"still trying to find my VIN looked everywhere (I think)"

carb-strip1.jpg

carb-strip2.jpg

carb-strip3.jpg

carb-strip1.jpg.e7b1ae49c7abe24891666c46c62cac3a.jpg

carb-strip2.jpg.00500ec51bef0a481502a0950af3940e.jpg

carb-strip3.jpg.5904a62f643cfc0f9ad0a3b93388cdef.jpg

Share this post


Link to post
Share on other sites

I have a 1992 big bear 350 who's carburetor has two cables to it; one to the front and one at the top.  I want to install a new carb that requires just one cable to the front.  Which one of the cables do I use from the old set up? [email protected]

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By MarkinAR
      What is the opinion on carb kits? What's one of the better brands of aftermarket? OEM is always preferred but not practical, chinese cheapie is never a good option. 
      Thoughts ?
    • By DUBLT
      Looking to purchase a windshield for my ATV, suggestions of what to buy with quality in mind and will fit without doing any modifications. 
    • By Ted Aregi
      I've got a king quad 750cc has anyone converted the fuel pump relay to a stronger fuel pump relay on there king quad?
    • By josephnbl91
      My four wheeler when i first got it seemed like it was very slow when i first got it and it had no throttle response so i replaced the belt and cleaned all of the rollers thinking that would solve the problem from what i read on the forums. well it turned out that it wasnt. so i went to the next thing i took out the injector to check it out and i seen that there was a tiny bit of debree in it so i cleaned it and it seemed to improve a little bit. but still did not solve the problem. i later found out how to find the trouble codes out from the lcd screen using a paper clip on the diagnostic port and it showed the code which stood for no codes C00. i also forgot to mention that the throttle position censor is working perfect. before i started all of this the four wheeler ran just not to its potential. after my friend and i did the trouble code test the bike wouldnt even start anymore and the injector would spray for a few seconds for the start up then it stops and the fuel injection light comes on and blinks. the four wheeler wouldnt start anymore. i took it over to the local shop and they hooked it up to the computer to see if there was any codes and it still showed it was free of codes. they hooked it up to the fuel pressure gauge and we found that it was making 22 pounds and it should be making around 43. i then bought a new fuel pump and put it in. it now starts and runs for a few seconds and then it stalls out and the fuel injection light comes on again. which then leads me to think it is the ecu now but i want to be sure before i invest around $500 more into it. any opinions on whether or not anyone thinks this is the problem or if they have had a similar problem before would be really appreciated. sorry for writing a novel and not spelling very well. also i forgot to put the year in the title it is a 2007
    • By My kiwi shed
      Hi there everyone. Just seeing if there is advice on a problem I have before I start digging too deep. 
      I recently bought this creally nice 2004 King quad ltf300 with only 2400km..
      Everything things works great except when engaged into 4wd or diff lock it has a clicking noise ( sounds like broken teeth etc) are the front diffs known to blow?  Or the transfer from engine?
      I am yet to test on some loose ground to see if I'm getting drive at front .
      I will be driving in to find problem in next few weeks but thought I'd see if anyone might know what it is first. Cheers


  • Similar Tagged Content

    • By Alan Callison
      I just got a 2004 Yamaha that needs some work.Its got wet brakes on the front that Im trying to get working.My problem is the brake lever.This the lever on it now.On the master cylinder it has a cable in it that has the wire that fits in a slot inside the lever itself but this lever isn't made for that.I dont know if whoever had it before didn't know what they were doing or what but its the wrong lever for this machine. Can someone point me in the right direction here? I looked at the Yamaha website and the schematics only show a part that looks like this one here. Again,I have a 2004 Yam 400 Kodiak 4x4 and its an automatic model. BTW,the master cyl. was bone dry. I was gonna change out the rear brake shoes and when I went to pull off the wheel,get this, each wheel stud had 2 different sized washers holding the lug nuts to the wheel rim. The stud holes were so worn out it had worn away the base of the studs and the holes were the size of  quarter! Im lucky someone didn't die while riding this! A word to the wise.Pay attention to what you buy.Look carefully and keep a keen eye out. This was my fault because it was the 1st ATV Id ever bought and I didnt notice alot on this machine so I guess I count myself lucky in that I didnt get hurt nor did anyone else who rode it either.
    • By dwo0100
      Took my wolvy for her first trail ride past weekend. Got home and cleaned all the mud and dirt off. Went to take a spin around the neighborhood and started having issues.
      When you are about 1/2 to 3/4 throttle the RPMs will sudden spike way up with little difference in power to the machine. Once you shift to the next gear it will increase power/rpm consistently then same thing happens and you get a sudden RPM spike. It also seems to recreate the problem if you are low in the gear and try to punch it...High rpm with no power increase. If you shift gears and gradually increase throttle she will increase power and RPMs consistently but if you shift and are more than 1/2 throttle it will increase power and RPMs fine until you get about 1/2 to 3/4 way through the gear then you get the same RPM spike...
      Hope I am explaining this clearly. My truck did a similar thing once and it turned out to be a whole new tranny...hope this is a different issue. Thanks for your help guys and gals.
    • By BDurf94
      Wondering if anyone has an idea on what's wrong with my atv. I have a 2004 yamaha bear tracker 250. It runs perfectly fine in idle, but when I give it throttle it dies. Any suggestions are appreciated.
    • By b1jackson
      I purchased my kodiak earlier this winter. It was a being stored in a heated shop however when I went to pick it up, it was sitting outside in -20 and the throttle was froze shut. The bike seemed very clean with no mud on it so perhaps the PO washed it before storing it and some moisture got in the cable.
      My shop is unheated but in an effort to get it going, I made a little tarp tent and stuck a construction heater under it. Throttle cable came free and the bike started up an ran fine. 2 months later the bike is just sitting in my shop not being used. The throttle still freezes shut when the shop is cold but today, it was warm enough that it was free. But I wonder if there is an issue with the choke cable sticking? The bike seems to flood and won't start.
      I built my tarp tent again and warmed up the quad with the heater. Not sweltering hot but warm. I could get the bike to fire a couple times but then it seemed to flood again and wouldn't start. So is there something causing the choke not to work related to the cold? The lever seems to flip up no problem but not sure if it is doing something on the carb end causing it to flood and not start. The plug is new, spark good, and a nice mist of gas comes out of to piston when it's flooded.
      I don't want to tear into things if I just have to wait for warmer weather but would still like to get some early spring riding in. Any help?
    • By bigisland
      Hello, I have a 2005 Suzuki Eiger Quad runner. 400 4x4 Auto
      Starts ok. But when I push on the throttle, it stalls. Maybe the carb needs adjusted?
      There is some kind adjustment wheel that turns. I suppose this adjust fuel/air mix to carb. Either way I turn that, it still stalls when gas applied.
      Our Suzuki dealer is no longer here, Honda will not work on it...
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...