Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Dra O
posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
-fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
-along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
-I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
-can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
-it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
-I THINK it has a mikuni model x carb - diaphragm is ID 26mm OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
-last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
-any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
By Dwight Williams
Hey everyone, I've been scratching my head over this for most of the day. I bought a couple of Bayou 220's, got them running (they've both been sitting), and started tweaking and fixing small things. One of them is mostly done, the other had an aftermarket carb on it and I've been trying to sort that out.
Anyway, while adjusting the carb it died a few times, I restarted and moved on until it died and wouldn't restart. I figured maybe I'd flooded it or something - after further attempts I realized I had no spark. Since I have two identical machines I have many parts at my disposal. I've swapped the CDI, spark plug and coil with no luck. I have good resistance readings from the stator and pick up (135 and 110 respectively), I don't have a peak voltage meter but I measure around 53VAC on the stator when cranking. I have a 4 wire stator, not an alternator like the newer ones. Grounds look good, I've checked the kill switch by verifying that it and the ignition switch grounds the black/yellow wire to the CDI. I can turn the engine slowly and see the pickup short the meter as well, seems normal right? So far everything I've checked looks the same on both machines. I've got the service manual and wiring diagrams. Do these readings make any sense? I'm obviously missing something but I'm stumped. thanks!
By Mike Johnson
Does anyone know what the 3rd item is behind the battery on this ATV ? I know 1 is the, solenoid1 is the CDI box, what is the 3rd.
By Mike Johnson
Hello again guys ,. I have a Quadmaster that has a very bad lean to my passenger side wheel. I replaced the a arm bushings with no change in the lean, I see no bent parts and no adjustments available. It's always been there since I got it but became really noticeable when I put the lift kit on it. I'm going to add a picture of the problem if allowed.
Anyone going shopping on this Black Friday? Eraly Bird 4am specials? Any crazy shoppers out there?
Check out this site: Black Friday @ GottaDeal.com - The Official Black Friday 2007 Deals Site
Also Walmart has some early online specials: Advertised Values - Feature - Wal-Mart
Similar Tagged Content
So when im ridding in high gear randomly sometimes it will go into a persay limp mode and only allows a max of 30kmph and it sounds like a rev limiter, what would cause this and how to eliminate this all togeter as in the new ones with the over ride switch. its the sound that it does in low range or reverse. i want this gone period when i get stuck in mud i cann spin tires fast enough. and while im in high gear i dont want this happening. if you need more details the easier way of getting a hold of me rather then the forum is my email [email protected] i dont have time to check back here oftern but i get my emails right away.. thanks guys
By Christian Brindle
I've already posted here once about this ATV. Lots of people suggested i check the cam and after a couple months i finally got around to attacking it. I got it all apart and got the cam/rockers out. I'm almost positive they need to be replaced, they're pretty scored up and don't look too hot. Just wanted some final opinions before i drop the money on it. I'll also take feedback on the new cam i've chosen.
New Cam: https://www.amazon.com/hz/wishlist/ls/2GM2J05FQQPCD?ref_=wl_share
i have a 2000 suzuki king quad lt-f300f that i picked up as a project bike. it didnt run well when it was parked outside 5 years ago. it cranked after putting fresh gas - but would not run below half throttle, i took apart the carb, cleaned debris, and re-assembled. i suspect that the pilot needle is sheared off - it never protrudes into the throttle body through the pinhole. now to get the bike to ALMOST idle, the throttle idle adjustment knob is all the way up/in. the pilot needle is turned almost all the way in/up (if i understand correct, it should nominally be out 2 1/4 turns or so). and like i said, it will ALMOST idle. floods easily, rides rough.
wanted to hear from those more experienced than me with suzukis - and im self-taught atv repair, so dont laugh too hard if my verbiage/part names is way off.
facing the driver's side of the bike [US] there are three hoses on this side of the carb. without a service manual or way of knowing what was messed up before i got it, i think i have them right: front hose as a vacuum to the petcock, middle hose as vacuum to the fuel pump, rear hose as fuel line from the fuel pump. running the bike in prime position results in flooding even while riding. with all hoses disconnected from the carb, fuel slowly drips from the vacuum line connected to the petcock.
so just my speculation is that the diaphragm in the petcock is split, and the pilot needle is broke off - causing my inability to not quite idle and the rough ride. this suzuki is hoses and cables everywhere compared to the honda ranchers and yamaha warriors i am used to. I would like to have a plan rather than: replace everything at once.
is my speculation on the right track, or could something else be at play? say, if the compression was non-existent, would that cause non-idling? i am all ears, look forward to the input.
I traded my dirt bike for a 2000 arctic cat 500 semi automatic. when i went to go pick it up the guy said it didn't get spark, so i thought it was going to be something simple like a coil. well it wasn't. first thing i did was take all the plastics off to get easy asses to every thing. so i bought a brand new battery for it seeing if it got power, it didn't. the dash wouldn't light up neither would the lights, so then i tried to see if the starter worked it didn't so i jumped the solenoid and the starter started turning over the motor. so i bought a new starter solenoid, when i installed it the electric start still wouldn't work , so i bought a new kill switch and starter switch that goes on the handle bars, when i installed it, the electric start still wouldn't work. so then i went to see if i could get spark by pull starting it, i didn't get any spark, so i bought a new spark plug, and guess what, still no spark, so then i bought a new coil for it to see if that would fix it. so i installed the new coil and guess what no spark still and still no power to the dash. so to sum it up i'm not getting any power any where to the four wheeler. so i cleaned all the leads and plugs and still nothing. so then yesterday i took the wiring apart to see if their was any frayed wires, and no their wasn't. does any one have any ideas what this could be i'm up for anything. also if any one knows how to bypass all the wiring just to get it to start i open to that to, or if someone knows where i can get a wiring diagram.
i have recently purchased a yamaha kodiak ultramatic 400cc. it is used and sat outside for a long time. i have done a lot of work on it and got it to run sort of. when i try to start it, it will start and run for a little bit then it will die, the time it runs varies. it has a new cdi, spark plug, and stator. most of the time it wont even start it just cranks over. there was one time that it started up right away and ran perfectly but the next time i tryed it wouldnt start. before that one time every time it started and ran it had a popping sound. i cant figure out why it wont run. any help would be muchly appreciated! thanks!
Recently Browsing 0 members
No registered users viewing this page.