Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

sirdivealot

Yamaha Timberwolf Electrical Problem - Electric Start and Lights Not Working

Recommended Posts

Hi folks, I am new to this forum and signed up hoping to get some advice as to what the problem is with the electrics on my timberwolf.

The quad is a 2000 4x4 model, just bought it on the cheap a few weeks ago with electric start and lights not working. The starter makes no noise and no attempt to start whatsoever when the button is pushed and the lights dont work at all. It has a battery that has charge in it, so dont know why it wont just run off the battery, could it be a fuse?

I saw a thread on here about electric start not working on a timberwolf, I got some info from that but think this problem may be different so thought I'd make my own thread.

Any advice would be appreciated

Cheers

Share this post


Link to post
Share on other sites


i'd check the fuses, i think it's an inline fuse on that bike. i'd also get a votage meter and get some readings where the current doesn't show up. you could try jumping the starter at the solenoid/starter relay. if you have a meter, you could also test the battery. a bad battery won't make everything work ...

Share this post


Link to post
Share on other sites

I'll try get my hands on a meter today and test for current and chceck battery. Though inclined to think its not the battery as I was told it has charge and doesnt even make a clicking sound when pushing starter button. Hope it is the battery though, would make a cheap fix.

Thanks for the reply

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By barracuda420
      Hi, I'm new to ATV/UTV's and am looking for any advice that would help to repair my 2018 Ranger 500.  I got it from an insurance auction and have never owned one before.
      It looks like it was sunk deep.  Found rocks and sand in the roof, milky oil in the air filter box, water in the fuse box, etc.
      So far, I've cleaned the air box out, vacuumed most of the rocks and sand, checked the engine, trans and diff casings for cracks/leaks.
      The battery would not charge while connected so I know there is some short somewhere...probably the wet fuse box.
       
      I plan on drying out the fuse box and all connectors with a hairdryer tomorrow, check the fuses, remove/dry out the ECM and disassemble/clean the air intake.  Then install the battery and see if i can get it to key on and see what kind of lights I get.
      Need to know what to expect with the engine/trans...
      Thanks.
       
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By Mike Johnson
      Does anyone know what the 3rd item is behind the battery on this ATV ? I know 1 is the,  solenoid1 is the CDI box, what is the 3rd.
    • By Mike Johnson
      Hello again guys ,. I have a Quadmaster that has a very bad lean to my passenger side wheel. I replaced the a arm bushings with no change in the lean,  I see no bent parts and no adjustments available. It's always been there since I got it but became really noticeable when I put the lift kit on it. I'm going to add a picture of the problem if allowed.

    • By Daniel Gibson
      Working on a bayou 220 that has been ran extremely hard it's whole life. Literally had almost an inch thick dirt/oil covering the motor. Yeah that bad. Surprisingly it runs though. I cleaned the carb and tank multiple times. They're clean enough to eat off of. Readjusted valve lash and set timing. Was about 3 teeth off. It cranks good and runs good only problem is I have to cover the carb intake basically choking the hell out of it for it to start. The com choke works fine. It does this each time I start it regardless of temperature both ambient or motor. Wth? Compression is at 115psi I get 130s if I put a little oil in the piston chamber. Please help. Thanks 
  • Similar Tagged Content

    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By alexcross324
      Hi all, I try to find this manual in the threads but you have a lot of stock here
      Cannot find this particular manual.
      I found it for YFM200 but not sure if they are the same.
      Thanks if you could help me with that.
      Im new here so if I did something wrong, please tell me.
    • By Suzuki24
      I have an 04 ltz and it started sputtering a little bit while going down the road and I was low on gas so I just figured that's what it was. But now I can't get it to start I completely cleaned the carberator put a new spark plug and coil pack in it and all it does is turn over. It has compression it's getting fuel and it is sparking but all it does is turn over any idea what it is??
    • By davidwestfall
      looking for direct shift shifting lever that properly fits my 2003 Yamaha warrior 350 and fits my foot the same as a stock 2003 Yamaha warrior 350 shifting lever fits my foot
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...