Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Artifice

1997 Scrambler 400

Recommended Posts

Hey guys, I just got a '97 Scrambler 400 4x4 as a side project to work on through winter. I was wondering if anyone here could give me any great advice as to where I can get parts or even a service manual for this bike. Ive been told these are not too easy to come by.

Also Im very much used to working on Honda's so if there is anything crucial I should know about these before tackling it I would greatly appreciate the advice.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Sonders
      It appears that the Service Manual thread at top of forum is dead as all the links no longer work.  I'm actually looking for service manual for a 2000 KVF300 Prairie that I just picked up.  Does anybody have link to one that they can share, or know where I can find one?  Thanks in advance for any help.
    • By barracuda420
      Hi, I'm new to ATV/UTV's and am looking for any advice that would help to repair my 2018 Ranger 500.  I got it from an insurance auction and have never owned one before.
      It looks like it was sunk deep.  Found rocks and sand in the roof, milky oil in the air filter box, water in the fuse box, etc.
      So far, I've cleaned the air box out, vacuumed most of the rocks and sand, checked the engine, trans and diff casings for cracks/leaks.
      The battery would not charge while connected so I know there is some short somewhere...probably the wet fuse box.
       
      I plan on drying out the fuse box and all connectors with a hairdryer tomorrow, check the fuses, remove/dry out the ECM and disassemble/clean the air intake.  Then install the battery and see if i can get it to key on and see what kind of lights I get.
      Need to know what to expect with the engine/trans...
      Thanks.
       
    • By Randel1
      I recently read an article about restoring or at least improving the looks of faded and discolored plastic body parts. In the article it suggested using a 50/50 mixture of boiled linseed oil and paint thinner. You mix it up and apply it with a brush or rag to rub it in and remove the oxidation. I curious to find out if anyone has had experience with doing this and what was their short/long term results of doing so. I would hate to try it and find out that a few weeks/months down the road my plastic body parts self destruct.   
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By oxidized_black
      Clymer ATV Manual - Yamaha Raptor 700R
       
  • Similar Tagged Content

    • By Billie
      :confused:need a repair manual or help in what to look for thank you Bill
      for you muddober to make clear to you the neutral light and the gear light
      do not light up win shifting fuses are good Iuse my CAt for hunting im dissable the atv is my leag s thank you
    • By kiwisteve
      Hi Folks
      MY Ltf 400 has power and electric start turns motor over, but wont start...
      seems no spark
      im told stalled in paddock and wont start again
      any suggestions please
    • By izzydum1
      Any ideas on what would make a coil not fire? She was running fine, then began slow start. Now wont start at all.
    • By Jesper
      Hi guys
      Does anyone have a link to a service manual for the 2008 KingQuad fs 400 4x4.
      I would be very happy to get my hands on a file
      Thanks. :-)
    • By switch
      I have a really dumb question. My big bear came half apart and I am not sure how the timing chain guide is supposed to sit in there. I have the entire top end cleaned, bored, new piston, gaskets, etc. I do not see anywhere in any manual or thread where it shows how the chain guide is installed or held on place????? Also should it be the same height as the other side???
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...