Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

moose74

Yamaha Grizzly 660/700 Swap Into 600?

Recommended Posts

Can a grizzly 660 or 700 engine and front locking differential be put into a 600 frame/bike?Has anyone done this or know of it being done?Also will the newer locking front diff from a kodiak work in a older 350 wolverine?Thanks

Share this post


Link to post
Share on other sites


That's a good question, I don't think so, but I could be wrong.

* Edited thread title for better searches/responses.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By StolenATV
      Taken from my car port around 0330 and was taken by at least 2 people found footprints pushing the quad all the way to the road (80 yards)
      The post 2012 Yamaha Grizzly 700 EFI 4×4 Stolen appeared first on STOLEN 911.
      View the full article
    • By mothrottle
      The VIN on my 2018 Kodiak 450 is not where it's supposed to be. I bought this used. Is there another "hidden" location where I can find it? Need the number for insurance co. Thanks in advance.
    • By cliffyh
      Hi,
      Have a 2005 grizzly 660. Just recently started backfiring and showing incorrect speed. Lifted seat and messed with wire going to starter relay, it stops for a bit but seems to come back.
      I ended up pulling all the pins out of the connector for the relay and added new pin/connectors for all 4 wires. fixed it for a little bit but came back shortly after. This was a new starter relay i installed a few months ago. Anyone know if a bad starter relay would do this? 
    • By Sp33dy0000
      Hi can someone please give me some sort of idea I have a Yamaha 600 grizzly four-wheel-drive I have put a new coil and a new stater and Pulse stater on it with new plug and steel can’t get any fire
    • By David Miller
      Does anyone know how to access the check engine codes on a 2018 450 sportsman. Just changed battery and spark plug . It runs fine but the light is on and I need this to plow snow and need it reliable. Any ideas . Thanks
  • Similar Tagged Content

    • By Ajmboy
      Here are my 2004 Yamaha Grizzly photo albums if anyone is interested in checking out. 😎
       
    • By Ajmboy
      Took the power washer and cleaner up the grizzly a bit.
    • By Sp33dy0000
      Hi can someone please give me some sort of idea I have a Yamaha 600 grizzly four-wheel-drive I have put a new coil and a new stater and Pulse stater on it with new plug and steel can’t get any fire
    • By YamahaGrizzly
      not sure where to post this but,
       
      I have a 2016 yamaha grizzly 700 with a blown up transmission (again).
       
      I was wondering if a 2015 Yamaha grizzly 700 Main drive transmission shaft and gears shift drum will fit on my 2016?
    • By David Cameron
      The small waterline insert for the hose that goes from the water pump cover to the thermostat housing has corroded off. I only need the insert on top and behind the thermostat housing that the hose goes over and can't find just the insert. It looks like it may be pressed in. I've have been told the entire motor housing needs to be replaced. The pic with the red line indicates where the hose and insert would be and the insert looks like the pic of the water pump  Any ideas would be really appreciated.
       
       



  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...