Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Goodwrench

2005 Suzuki Eiger 400 - Mud/Fender Extensions

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By swensy7
      Hey all new to the forum.... We ended up picking up a 2006 Suzuki z50 quad sport and took it camping this weekend. The guy said had a new top end and just put on a new belt. Seem to work fine for a little bit and then it lost power at the rear wheels. Belt was not in bad shape took a look but it just did not seem to have enough power to get my little guy moving. I pick up the rear end tires would go. Set it down lacked all power.   Any help would be greatly appreciated it did run like a top also.      To add to the bad news on the way home I ended up losing the seat so if anybody has one even if it's in rough shape would love to get it or if you have any ideas open to suggestions......
    • By Cj Winds
      I have a 2005 Yamaha Kodiak 400 Automatic. It has an oil leak inside clutch cover. The middle gear has two oil seals, the front seal is leaking engine oil into clutch area. How do you change the leaking seal?
    • By Aleksandr Boreesenko
      doesn't idle at times but sometimes when it does as soon as I touch the throttle it just shuts off, what could possibly be the problem? I thank you very much for any help, Thanks.
    • By wwdubose
      I have two 2003 Suzuki Ozark 250s, both 2-wheel drive.  Last time we rode them about a year ago, the red one was not running well, didn't want to idle, backfired a lot.  The green one ran fine. 
      Fast forward...I ordered a carb kit for both of them, thinking the red one has some trash in a jet.  Both of these ATVs have had little use and I've always ran the gas out after use (put an inline cutoff valve in gas line).  I pull started the red one to verify it was still running bad.  It will start and idle, but as soon as you give it any throttle, it dies instantly.  Give it a little choke, dies instantly.  Took the carb apart and it was spotless.  Went ahead and cleaned all the holes with carb cleaner and blew everything out with compressed air.  All new jets, main jet holder, and needles.  Put it back on and nothing changed.  Starts, idles (not for a long time), but dies as soon as you give it gas.  Same happens when you put the choke on.  It does the same thing when I try to run it turned to prime on the petcock as it does in the on position.
      Not an air filter issue.  It is clean and it does the same exact thing with no filter on it.
      Thought maybe there was a float issue or maybe a damaged diaphragm, so I took the carb off the green Ozark and put it on red.  Started up and initially ran normal and revved for about 10 seconds and then started doing the same exact thing.  Starts, idles (not for a long time), but dies as soon as you give it gas.  Same happens when you put the choke on. 
      So...not the carb
      Thought maybe vacuum petcock was bad, but there's no gas in the vacuum line going from petcock to carb and gas flows freely when on prime.  I even plugged the vacuum line at both the petcock and carb end and tried to run it with valve set to prime.  Gas flows freely, but does exactly the same thing.  I unscrewed the screw at the bottom of the bowl and gas flows thru carb and out bowl drain line when petcock is set to prime.
      So, I'm assuming petcock is good?
      Checked spark plug and it wasn't fouled.  Reset gap, didn't help.  Will swap plugs between Ozarks tomorrow but I don't think that is it.
      Anyway, that he history and now you're all caught up.  Scratching my head.  Valves? These were bought at same time and have had little use.  Suggestions?
      Thanks!   
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...