Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

bobski

2007 Arctic Cat 650 H1 - Carb Problems

Recommended Posts

2007 650 H1 with dynojet jet kit. I changed pilot jet to a 42. Now when I let off the throttle it does not return to idle. It takes a noticable amount of time.

Share this post


Link to post
Share on other sites


Thanks for your intrest. I did the muffler mod I read in some of the forums. I have 2" snorkels dynatek cdi dynojet jet kit with 42 pilot and 145 main. I put the 42 pilot in when I did the muff mod. Some jetting articles I read said the pilot jet is too small. Have'nt time to mess with it so I was hoping someone had similar problem

Share this post


Link to post
Share on other sites

Did u do the slide mod? Make sure the quad is warmed up also so u know your choke is open. That might help. Also make sure your air filter is clean. If you jet now u will have to rejet in the spring.

Share this post


Link to post
Share on other sites

yeap slide mod. and it does it after its warmed up. It is anoying when riding, you let off and t keeps going.When I get time I will check for leaks and go through carb again. I will read over " jetting 101"

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By AimlessMoto
      Hey guys, new here, but haven't found ANY answer to my specific problem on a Suzuki dedicated ATV forum, so here's to hoping!
      I acquired a 95' Quadrunner 250, 4x4, (LT4WD) for practically nothing with no spark. The PO had tossed in a used stator which didn't fix the problem... so I went all routes (though cheaply) to narrow down the initial problem of no spark. 
      Plug, coil, CDI (caltric) and stator w/pickup (caltric) were purchased and installed. And it RAN, but bogged horribly and would not rev past 1/4 throttle. 
      I checked fuel flow, vacuum lines, all the normal stuff, no issues. I decided to check the valves and cam... well, there was one problem. The cam was 1mm under the lowest spec in the manual. So, in-came a new cam, Stage 1 Hotcams... also threw in a new set of shindy valves, lapped them, replaced the valve seals, and the timing chain. 
      Back together again (w/stock airbox and new oiled filter). Now it idles even better, still boggs at 1/4 throttle, but will rev past it if you hold the throttle open for a second. Ahaha... success!
      So I was able to ride it above 1/4 throttle once I had momentum... could shift through the gears, all was good as long as I kept it over 1/2 throttle. Took a long enough ride to break in the cam properly at least so I won't have to worry about that. 
      Now, I start fiddling with the carb. It's clean as a whistle, stock, with stock jets (new replacement Mikuni jets). Same problem. 
       
      I start thinking, maybe this is fuel related and the bike is having an issue transitioning from idle jet to main jet... so I LOWER the needle by raising the clip 1 spot. Now it revvs up in neutral with no bog, but it boggs about the same trying to ride it. So I move the needle down again with the clip on the top slot. Better, but still has a bit of bog at 1/4 throttle. 
      The last bit of advice I got was to ditch the CV carb... so I sprung for a brand new Mikuni VM30-83 round-slide. Bolted it up, blew into the vacuum tube to fill it with fuel (no vacuum port on this one) and she fired right up... but there is still a bit of bog, it's just masked by the fact that I'm not waiting for the vacuum diaphragm to open. 
       
      So I feel like each little step brings me closer, but not perfect. I'm now wondering if this is still in-fact a carb tuning issue (I have some jets I can fiddle with and maybe lean-out the idle jet a little.) OR if the cheap-a** Caltric Stator/Pickup is what's causing these issues. 
       
      I have a 95' KingQuad with 400 miles on it... like new.. runs like a top... I've tried both the stock QR and the Caltric CDI boxes on it, and it revvs up and runs like a champ. 
       
      The only unknowns between the two systems are the carb, and the stator/pickup. My next step in troubleshooting is to rip apart the King Quad and test it's CDI on the Quadrunner... but considering there is no change to how it runs I doubt it will lead to a solution. 
       
      HOWEVER... I tried the stock CDI just recently after running the Caltric this whole time, and the bike runs like garbage. Hardly idles, and won't rev up at all. So, that is my one smoking gun telling me that it's either the pickup coil or the stator itself. 
       
      Has anyone had a problem even CLOSE to this? I can't image the carb would be causing this many issues, especially going to 2 different ones, both with stock jetting to OEM, and exhibiting the identical symptoms... the only change is when different CDI's are plugged in, or when the needle valve leans out the mixture. 
      Also, I checked the piston, rings and bore when I had it apart and they're like-new... no scoring, rings are loose, cylinder is still round and has honing marks still int he bore. Stock piston, stock bore size and it has 160psi compression. Battery is brand new, and I've tried 3 different R/R's, none of which change any symptoms, but slightly vary the charging voltage by .2-.5 of a volt depending on which unit. Also tried a new coil which changed nothing. 
      ANY help would be appreciated. Too much invested to not get it running right. 
    • By Gary Patch
      Hi my linhai 300 is hard to start and  engages gears at idle which is 1200 rpm was looking at cdi says on it 7500 rpm does this mean quad should idle at 7500 rpm as this would explain transmission problemb as idle is too high thanks gary
    • By John Ford
      i ordered a keihin carb for my 07 trx 90 and it fits nicely but the new cable they sent is way too long and i can't make it work.  the old honda cable cap [that fits on top of the carb] is too small to fit.  the keihin cap is approx 3/4 or 19mm.  honda cap is more like 1/2 in.  the keihin has a rubber boot on the cap where the throttle cable goes through . i don't know how to find the right length [most cites don't give the length].  i'm not sure how cables fit into that boot  and do i need to add the length of the boot to the cable?  the old honda cable is 28 inches total, but the cable movement is only approx 2'' which would not be enough to reach the actuator block on the keihin.  looking to find a throttle cable compatible with the keihin.  any help, please.
       
       
    • By Roy Anderson
      I have a 2002 Suzuki LT-F500F, and am a first time atv  owner. I rode two wheel bikes for many years, and now, two months in to being a new at owner, am just not enamored with the thumb throttle, and I’m wondering if anyone has tried a conversion to a typical twist grip throttle as found on all motorcycles? If so, how do you like it?
    • By Fred Colby
      TPS on  Polaris  SPORTSMAN  500 efi 2007 shows as bad original part number is 3140173 bought the replacement part it came in as 3131705 the diameter of the ring on the face is 26 mm the original is 18 mm any thoughts on how this "factory" replacement parts fits as i cannot get it to go in?
  • Similar Tagged Content

    • By Paul Maple
      I have a 1999 Sportsman  500, it was running fine, than started to lose power in the winter, I adjusted the idle screw and away I went, than a few weeks ago it died, I have found that i am flooding the engine, compression was at 70PSI and due to the compression release mech. i assume i am good as it compared to the same PSI on a 2000 sportsman 500 i have. i cannot start the atv unless i go full throttle and it starts an runs for about 30 sec than dies, again it is flooded. i ordered a new carb off ebay as i could get one for around $40. put that in same issue, i have checked the timing, (good), valves out of adjustment i adjusted to .006 still same issue, i have found the exhaust lobe and rocker arm to have some wear, i have ordered new ones, but am looking for any other input in this area as well. would the exhaust cam and rocker arm cause the engine to flood? i have used a bore scope and the piston liner has good cross hatching still? any input would be great.
    • By Tubecatgs
      A friend of mine has this Bayou 220 that started running bad and parked it a few years ago. I foolishly volunteered to take a look at it. I noticed right away the choke plunger on the carb was broken and probably the reason it was running bad but now the old gas was evaporated and like turpentine. Before i even tried to start it, i drained/ thoroughly washed the tank out, new fuel filter, new fuel lines. Blew air through the petcock etc. Changed the oil and filter and air filter and new choke plunger and cable. I disassembled the carb and rebuilt it with a kit. I cleaned the main jet with solvent and poked a wire through it to make sure it is clean.. the engine now fires right up with the choke on and dies when i take the choke off. I adjusted the air/fuel screw to about 1.5 turns out and the idle screw about 2.5 turns out. The rubber boot between the carb and head does not have any cracks in it so I don't think it is leaking air. I originally had the clip on the needle on the second from the top ring... when i moved it all the way to the bottom it starts, runs and idles really fast and will idle eeally high with the choke off but if i adjust the throttle cable and/or idle screw to a slower idle it will sometimes stall but the idle will go up and down every few seconds and when you give it gas there is a hesitation... i tried moving the clip down to rhe second from bottom and same problem... i replaced all the parts in the pic to the top right. However, there appears to be a small o ring, washer and spring left over from the kit... i did not see these get removed..... a) any idea if where these extra parts go and if i need them and b) any other ideas on why i cant get it to idle right or carb adjustment ideas?
      Thanks
    • By bradley nelson
      What is the best and easiest way to tune your carburetor? Any tips or tricks?
    • By LTZ-Zach
      So i was riding the other day and my quad randomly shut off. It started back up and ran completely fine for a little while and then it started idling terribly.
      I cleaned the carb and changed all the jets and everything except the float due to the rebuild kit not coming with one and it actually runs worse then it did before.
      It will run and idle decent now but when I give it gas it dies.
      Does anybody know what could be wrong?
      I also changed the spark plug and air filter along with the oil and oil filter.
       
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...