Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

laxer35

Malfunction... Baja 90cc atv?

Recommended Posts

Hi, I have a baja 90cc atv. The battery went dead and the atv was sitting there for about a month. I got a new battery and now it will start up for like 2 seconds at full throttle without me touching anything after clicking the start button and then turn off. Its not moving because theres no clutch. Any tips on how to keep it running???????

Share this post


Link to post
Share on other sites


Hi, I have a baja 90cc atv. The battery went dead and the atv was sitting there for about a month. I got a new battery and now it will start up for like 2 seconds at full throttle without me touching anything after clicking the start button and then turn off. Its not moving because theres no clutch. Any tips on how to keep it running???????

Sounds to me like a fuel supply problem and or a carb problem. I'd start with checking the fuel supply flow from the tank and if thats good move on to the carb. However if the fuel is older than a month old I would remove the tank and clean the tank and then add new fuel along with a good fuel stabilizer. Fuel today goes bad pretty quick and can gum up a carb and cause the throttle needle to stick too. Hope This Helps, Whip

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ed Zeppeli
      So I fired up the quad the other day and let it idle for about 5-10 minutes and it ran great then died.
       
      I go to check it. No lights on dash, nothing.
       
      Check the main fuse and it's blown. Key's off/out. Put in another and it blows immediately.
      Pull out the meter and see that on the non-load side of the fuse holder there's continuity to ground.
      Check all obvious things. Wiring diagram. Connectors. Frayed wires. Bad grounds.
      Battery measures ok at 12.8v.
      I'm dreading taking off the front plastics but I suspect the regulator/rectifier. The wiring diagram shows the red wire (the suspect wire) goes to the ignition switch and the regulator/rectifier.
      Anyone else experience something similar and/or have any troubleshooting tips that may save me the grief of removing the plastics?
       
      Thanks much,
       
      Warren
    • By Adrian Ciotinga
      The title pretty much explains it all. When using the starter I can hear it spinning but not engaging the engine. The wheels also do not engage with the wheels when the clutch is out. The motor has compression if that helps.
      I am new to engine work and repair and I bought this quad with the idea of fixing it up (not knowing the full extent of the damage). The previous owner said it ran but sat for a year (I don’t believe that for a second after opening it up) and had bought a few new plugs and a starter motor, none of which fixed the issue.
      Any help would be greatly appreciated!
      I have attached a few pics of what I think could be wrong.




    • By gouletp
      The thing sat since Christmas 2018 and while I decided whether to replace the starter (which I finally did today).  I am not sure if I added fuel stabilizer or not but chances are good I did.  I kept the one year-old battery well charged during the winter.  It turns over well but won't start.  I have a blue spark on a brand new plug.  When I pour a bit of fuel down the cylinder, the engine starts and runs for a few seconds (once for as long as about 8 sections) and then dies.  Even before adding fuel to the cylinder I noticed that the spark plug was wet with fuel.
      The air filter looks a bit dirty so I removed it just to see if the engine would start better but it made no difference.
      If the fuel did not contain stabilizer then the carb may be gummed up.  I don't really want to remove the carb to do a thorough cleaning.  Is there a product I can spray into the carb while the engine turns over that will clean the carb?
      Any other suggestions?
      Thank you
    • By Resurgence Small Engine Inc.
      Recently, Jonathan has been repairing & reassembling a client's 1983 Big Red Honda ATC200E. In this video, he gives an overview of how he approached diagnosing the ATC and creating a plan for the project.
       
    • By LMI
      I wanted to share an experience and a fix.
      Headed out was following a pole line, was looking for a cross track that may take me to this speckle trout looking spot on a creek.  All paths and semi paths... failed.  Second objective was to reach a speckle trout lake that has been recently stocked... followed 1 trail to dead end, followed second trail to dead end.... while investigating options on foot and the quad idling it died.
       
      It wouldn't start.  eventually it did... and when it did … it was essentially a pinned idle.  activating the throttle did seem to speed it up but it wouldn't knock out of the racing idle.  couldn't put it in gear at that idle speed.  got towed out.
      when I first got the quad, I ran it off a trail and buried it pretty good in the soft snow... eventually winched out.  It wouldn't start.  eventually did and it was fast idling.  not as fast as this last time. but still fast.  it eventually seemed to settle and I got it in gear and by the time I was back to the truck was acting ok.  chalked it up to the bike being at a bad angle in the snow.
      My investigation last year lead to the throttle position sensor TPS.  how to jumper the diag block to see the sensor position on the display,.  I focused on this nearly sure it was a detuned sensor or broken sensor again this time.
       
      I tore down the front plastic and stuck my head into the TPS area to see what I could see.  What I found was that the throttle body assembly had actually come out of the mounting area (not sure what it is called).  the ring clamp was loose I could move it easily.  Hopeful, I tore down the air intake assembly above it (air filter...etc) removed a sensor clip and a hose.
      I backed off the clamp some more and was able to reseat the throttle body assembly.  put some blue lock tite on the clamp screw.  When I was cleaning off the air intake assembly to ensure I dropped nothing down the intake, I noticed the underside of the air intake "box" also had a clamp.  this screw was completely missing.
      I went to the hardware store, bought a metric replacement (brought clamp with me), seated the assembly, settled the clamp blue lock tite that as well... 
       
      quad fired right up, idled normal, idled up without hesitation and dropped right back off.  Cost of solution $3.87 CND for a pack of 5 metric screws.  moral of my story was don't assume an idle issue is a throttle position sensor problem... there are a number of other factors including air pressure, which I believe was my issue.
       
       
       
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...