Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

Does anyone know how or what kinda of tool to use to ajust the pilot screw on a 94 250 suzuki quadrunner. It seems that you can't get anything between the carb and the motor. I belive it should be turned out 2 1/2 turns out is this correct? Thx

Sent from my SGH-T989 using Tapatalk 2

Share this post


Link to post
Share on other sites


The only way I know of is to remove the carb. Suzuki manual says 2-7/8 for a new pilot jet screw. I was mistakenly under the impression it was supposed to be 1-1/2 and that is what mine is set at(93-LT-4WD). It runs fine, so I'm not going to remove it to mess with it.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Walter Awe
      I HAVE a 2002 big bear 400 4x4. I have two wires atacking to the front of the carb. What are they for?
    • By stinky
      I have an Outlaw 110 that will struggle to turn the engine over. Jump starting doesn't help other than the battery will drain LONG before the bike eventually starts, so is required. If you keep messing with it long enough it will eventually magically begin to crank fine and sometimes finally start. Once we finally get the bike to start and warm it up thoroughly, it will turn over and start just fine the rest of the day like nothing ever happened... next day it won't turn over again.  Internet research has found lots of people saying they replaced starters, starter clutch, wiring, etc. but with only about 50/50 success rate for their particular problems... and I never found anybody describing a problem like mine, so I'm looking for advice/experience. Would rather not just start blindly throwing parts at it. Does anybody have any thoughts/ideas?
    • By Wayne Starz
      I have a 2005 Suzuki Vinson 500cc automatic 4X4. I can only shift it in to park & High gear, it will not go in low or reverse, what's the issue & the fix?
    • By StolenATV
      ATV was stolen out of our 2016 Voltage 3305 Toy Hauler that was at Cutting Edge Collision for repairs. The rear locks were broken on the rear of the toy hauler and the ATV was Stolen. Cutting Edge Collision is in a gated and secured area
      The post 2007 Suzuki LTZ 400 Stolen in Tucson Arizona appeared first on Stolen 911.
      View the full article
    • By Finsdad
      Im new to the forum and the quad I just got. I want to change oil in in. Its almost impossible to find anything on-line. I know it takes 10w40 and know the oil filter location. What oil should I use? Is there a cross reference for oil filter. The closest dealer to me is an hour away. I have NAPA close and like the WIX or Napa gold filters. Also is where can I get a Manuel for it? Thanks
  • Similar Tagged Content

    • By JunkerG
      I am unable to find the default mixture screw setting for this Mikuni BSR33 carb. The screw only unscrews 4 turns and does not unthread out of the carb, (no way to clean it). When I took the carb apart to clean it the screw was set at 1 turn out. I bought this unit when it was only a few months old from a friend so I know it is the original carb. I know most carbs are set at 2.5 turns out, but would like to find out what this specific carb should be set for.
    • By stillsmoken
      Just wondering if there was a trick to ajust the pilot screw lol. I have a 94 suzuki 250 quadrunner and you really can't get a screw driver inbetween the motor and carb.
      Sent from my SGH-T989 using Tapatalk 2
    • By FTPVic
      2001 AC 300 Green
      When seating the fuel mixture screw is it supposed to protrude slightly? I can see the tip sticking out. Im just wondering if what I think is seat is actually to far in. Should it be below the surface already when I begin backing out 2-2 1/4 reset?
    • By KCOLLIS
      Hi all,
      I have a 2007 king quad 450 with starting/idle/power problems. My two boys had a go at it while I was away at work and now I found that the idle air screw was removed and I don't know about setting it up. I want to set this before I start on the other problems. New fuel pump, new injector, new foam air filter, error code reads -C00. Any help would be appreciated.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...