Quantcast
Jump to content

Kawasaki Bayou 300 Need Help


pathfinderz1

Recommended Posts

I have new plug in it but still weak spark.I have had snowmobiles but the motor on was easy to get to. I know some about power packs. I did down load the manual that was on here but does not give much on trouble shoting.

So if someone on here can give me some ideas on were to start and what to look for maybe I can get some good spark

Thank

Mike aka the pirate

Link to comment
Share on other sites

  • 2 weeks later...

Aw but if you niticed I sign my name the pirate That means I have one leg to work with. Plus to top it off I'm 72 years old. I have had snowmobiles old ones for 20 years and my main hobby is old outboard motors. Some of the newer outboard motor have had the power packs on them

Noiw these Quad runners are something new to me. So if I seen a little slow its just that these are new to me.

And I will take any help I can get

Thanks

Mike aka the pirate:biggrin:

Link to comment
Share on other sites

  • 5 years later...
  • 5 weeks later...
  • 1 month later...
On 2/5/2013 at 5:19 PM, pathfinderz1 said:

just got this boyou 300 don't know the year and need to find were the numbers are plus the spark is real weak and one other thing can't see any oil in the crank case fill hole and was wondering how to tell when its full. I did download the manual for this but not much info for what I need.

So help

Mike aka the pirate:aargh:

there is a sight glass with 2 marks in the casing indicating high and low levels below the fill cap. for the weak spark i have found a weak battery when using the starter will produce  a weak spark. but using the pull rope produced a strong spark.

Link to comment
Share on other sites

  • 4 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
    • By BruceG
      Hi guys. I have a problem where the quad will start and run well for about 5 minutes and then it dies. On inspection the airbox has oil in it (quite a lot). The oil is pumping through the cylinder head breather hose. This problem first happened suddenly. I have since done the top end including, piston, gaskets, rings and valves. I have also done the carb (not that I thought that this was the problem). The compression seems normal. The only thing that I can think of, is that I did not grind the valves well enough. Anyone experienced this? If so, how did you fix it? Any other thoughts?
    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
×
×
  • Create New...