Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

spitfire

1985 Suzuki LT180 - Carb Question

Recommended Posts

I am not sure if the pilot jet on my lt180 is plugged. I cleaned the four small holes at the bottom of the jet, but is there a hole that goes from top to bottom on the jet????

Share this post


Link to post
Share on other sites


Finally solved the carb problem after removing it a number of times. I cleaned every part except the center hole in the pilot jet. That's why I had so much trouble with the choke and high idle. The quad now starts first pull, idles up a little and goes to low idle after it warms up. I checked all the other carbs that I have and every one of the pilot jet center holes were plugged solid. I used a fine torch tip cleaner to unplug them. Thanks for the reply and info. I now have the Mikuni carb schematic on file. Will post some pictures, once I get the body work done.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Buick350X
      Exploiting a loop hole in the law, turn 4 wheeler into rev trike
      for a long while I have been trying to get a real 4 wheeler street legal.
      the problem is with the state laws, if it has 4 wheels, its a car and has mega more rules.
      If it only has 3 wheels, its a trike and can be made from cobbled junk parts held together with duct tape and they will plate it
      I wonder if anyone would have insight on changing a 4 wheeler over to a single rear wheel?
      [ I can't afford some $40-60,000 canam or super bike modded into a car, rev trike kit ]
      I want something I can truly ride year round on and off road. Ive rode enough old Honda 3 wheelers that I know I do not want a traditional motorcycle trike. So the single wheel has to go out back.


    • By Tiffany Rowland
      I recently purchased an 07 Honda sportrax and when I was checking the spark plug I saw the boot was ripped nearly in half. When I removed the plug it was blackened and covered in oil. How can I thoroughly clean the plug hole and remove any debris that is in there? Is there a small tube like vacuum or something of the sort made for stuff like this? The machine my dentist has would be perfect, maybe they do rentals! 😁

    • By Tiffany Rowland
      I recently purchased an 07 Honda sportrax and when I was checking the spark plug I saw the boot was ripped nearly in half. When I removed the plug it was blackened and covered in oil. How can I thoroughly clean the plug hole and remove any debris that is in there? Is there a small tube like vacuum or something of the sort made for stuff like this? The machine my dentist has would be perfect, maybe they do rentals! 😁
    • By Brad Leeson
      Can someone please tell me where the pilot air jet is located? I can't find anything other than on the pilot jet. It's on a 2005 yfz 450. 
  • Similar Tagged Content

    • By Ellery Zandt
      I have no idea where the antifreeze line coming off the thermostat goes too. The carb two nipples in the pic create a vacumme. Can someone help me on this please....!!! my email direct is [email protected]!!!!
    • By Ellery Zandt
      Does anyone have a redcat 250 or falcon 250cc that they can share where the two vacuum lines on the carburetor that you run antifreeze through I honestly have no idea where the lines are suppose to go to circulate the antifreeze. 
       
      Any help is greatly appreciated. 
       
    • By Paul Maple
      I have a 1999 Sportsman  500, it was running fine, than started to lose power in the winter, I adjusted the idle screw and away I went, than a few weeks ago it died, I have found that i am flooding the engine, compression was at 70PSI and due to the compression release mech. i assume i am good as it compared to the same PSI on a 2000 sportsman 500 i have. i cannot start the atv unless i go full throttle and it starts an runs for about 30 sec than dies, again it is flooded. i ordered a new carb off ebay as i could get one for around $40. put that in same issue, i have checked the timing, (good), valves out of adjustment i adjusted to .006 still same issue, i have found the exhaust lobe and rocker arm to have some wear, i have ordered new ones, but am looking for any other input in this area as well. would the exhaust cam and rocker arm cause the engine to flood? i have used a bore scope and the piston liner has good cross hatching still? any input would be great.
    • By Tubecatgs
      A friend of mine has this Bayou 220 that started running bad and parked it a few years ago. I foolishly volunteered to take a look at it. I noticed right away the choke plunger on the carb was broken and probably the reason it was running bad but now the old gas was evaporated and like turpentine. Before i even tried to start it, i drained/ thoroughly washed the tank out, new fuel filter, new fuel lines. Blew air through the petcock etc. Changed the oil and filter and air filter and new choke plunger and cable. I disassembled the carb and rebuilt it with a kit. I cleaned the main jet with solvent and poked a wire through it to make sure it is clean.. the engine now fires right up with the choke on and dies when i take the choke off. I adjusted the air/fuel screw to about 1.5 turns out and the idle screw about 2.5 turns out. The rubber boot between the carb and head does not have any cracks in it so I don't think it is leaking air. I originally had the clip on the needle on the second from the top ring... when i moved it all the way to the bottom it starts, runs and idles really fast and will idle eeally high with the choke off but if i adjust the throttle cable and/or idle screw to a slower idle it will sometimes stall but the idle will go up and down every few seconds and when you give it gas there is a hesitation... i tried moving the clip down to rhe second from bottom and same problem... i replaced all the parts in the pic to the top right. However, there appears to be a small o ring, washer and spring left over from the kit... i did not see these get removed..... a) any idea if where these extra parts go and if i need them and b) any other ideas on why i cant get it to idle right or carb adjustment ideas?
      Thanks
    • By bradley nelson
      What is the best and easiest way to tune your carburetor? Any tips or tricks?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...