Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

MadMan

1998 Yamaha Big Bear - Slow Throttle Response After Snorkel Install

Recommended Posts

I own a 1998 Yamaha Big Bear 350 4x2. I recently purchased a Submarine Snorkel brand snorkel kit for it which didn't fit properly, so I decided to build one homemade. I ran 1.5" PVC from the stock air box up to the front of the quad. It passes thru the front right fender and pipes into a 2" PVC mounted to a crash plate on the front rack. I connected the crank case breather line into the 1.5" PVC as well. I made a 2nd Snorkel on left side of quad which is a faux snorkel since it's purpose is to conceal the breather lines I have extended from the rr drum brake, rr dif., and carb. I took care to loop the breather lines a couple of times to prevent water from getting in, in the event I ever sink the quad. I also siliconed the air-box lid and used Dielectric grease on all electrical connections. I don't go swimming with my Big Bear but I do ride thru fairly deep water occasionally and I just wanted the snorkel installed as a precautionary measure for those unexpected dips u take when traveling across what u thought was a shallow puddle on the trail. LOL. Any way, since installing this snorkel my quad has an odd throttle response. When riding at normal speeds it's unnoticeable, but when hammering the throttle or fluttering the throttle the response seems to lag. I also notice if I'm in a gear too high for the slower speed I'm going the quad sounds like it's about to stall. I know normally u downshift the slower u drive, but it used to drive in a higher gear at low speeds and not bog down like it does now. I'm told I should re-Jet my carb. I'm pondering installing Dial a Jet. Any suggestions from you experienced riders? Removing the carb is a PITA and reinstalling it is equally fun. I've already rebuilt the carb prior to snork install. I like the concept of a dial a jet being able to adjust on the fly, but wasn't sure if it's the way to go. Please help. Any advice is greatly appreciated guys!

quadcrazy 01 snork.jpg

quadcrazy 02 snork.jpg

57d773458aea4_quadcrazy01snork.jpg.95a538b90aaa7f25371a1c027b4eab31.jpg

57d773458ed46_quadcrazy02snork.jpg.900e68bf2670511cb7b712b45aa73a17.jpg

Share this post


Link to post
Share on other sites


sounds like a rejet is in order. Ive heard nothing but good things about the dial-a-jet. I plan on one cause I went back to an open airbox but still like the option of closing it up when I go through deep water.

Share this post


Link to post
Share on other sites

Hey MadMan did you ever figure out how to fix your problem. I recently made a snorkel for my 95 Big Bear 350 and am experiencing the same issues. It idles fine and runs good in high gear, but when you give the throttle quick revs it sounds like its being sufficated and wants to die. I tried to adjust idle screw and fuel mix screw and no luck. Thanks.

Share this post


Link to post
Share on other sites

Soco499; Yes, I did fix mine. I adjusted the carb needle to remedy my problem with throttle. I opened up the carb, pulled the needle out, and moved the needle clip one notch down which raised my needle slightly. By raising the needle position it makes bike run a little RICH. My snorkel mod increased my airflow, so I needed more fuel to compensate. The bike previously was running like crap. It'd bog down when i would punch throttle from a stand still. Now throttle response feels right. My stock exhaust is rusted to Hell, so I am ordering a new DG RCM ll slip one exhaust from Amazon. I'm sure I'll have to rejet my carb afterwords. I'll keep u posted how the bike runs after the install. BTW I have discovered no one sells an after market slip on exhaust or these old Big Bear bikes. A stock Yamaha ugly steel can one cost more than a new DG pipe. I hope it's not a POS. Good luck with your Big Bear! These old Yamahas are bullet proof IMO.

Share this post


Link to post
Share on other sites


Hey MadMan did you ever figure out how to fix your problem. I recently made a snorkel for my 95 Big Bear 350 and am experiencing the same issues. It idles fine and runs good in high gear, but when you give the throttle quick revs it sounds like its being sufficated and wants to die. I tried to adjust idle screw and fuel mix screw and no luck. Thanks.

Its been a while since my last post. To recap, I have a snorkel and after market DG RCM slip on exhaust installed on my 98 yamaha 350 4x2 big bear. The raised the carb NEEDLE up a bump and changed my Main stock jet from #120 to a #145. Bike was running great afterwords. It was peppy and sounded killer. I recently had it in storage for maybe 4 months and now its running crappy. It doesnt want to idle for very long, keeps stalling. It drives fine with light or medium throttle but if I punch the throttle the revs stop. Its like a let off the gas when in reality Im holding it down. If I drive up steep incline the motor stops. It will then start back up once bike is on flat ground again. Could this be due to a sticky float in carb? This bike had a float that would stick about a yr ago and I chgd the needle valve set. Maybe it needs to be done again or a simple cleaning? I forgot to check the carb drain to see if it was pissing fuel last ride. Thats usually my clue the float is stuck. The needle valve set looks like its made out of aluminum and the tip appears to be dipped in rubber. Last time I changed it the alum looked pitted which caused it to get stuck in place and not move freely with the float. I hope its a simple fix. For an old bike this thing is solid! Yamaha built it like a tank and it drives like one too. LOL!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By dgk_mike
      It will go into neutral, 1st, 2nd, and reverse but nothing after 2nd gear. The shifter moves freely going up completely nothing but when you shift down it works. I’m not sure if it’s tranny issue worth messing with or if I should just buy a new one.  Overall besides that the thing runs like new.

    • By Asen_77
      Hi All,
      My name is Asen and I am from Eastern Europe, Bulgaria. Riding a Yamaha Raptor 700R and this is my first Quad wanted for a vey long time :)

       
    • By StolenATV
      Taken from my car port around 0330 and was taken by at least 2 people found footprints pushing the quad all the way to the road (80 yards)
      The post 2012 Yamaha Grizzly 700 EFI 4×4 Stolen appeared first on STOLEN 911.
      View the full article
    • By mothrottle
      The VIN on my 2018 Kodiak 450 is not where it's supposed to be. I bought this used. Is there another "hidden" location where I can find it? Need the number for insurance co. Thanks in advance.
    • By Admin
      Looking for Yamaha ATV VIN (Vehicle Identification Number) Number Decoders? Once you find your ATV VIN number off the tag on your Yamaha ATV, you can go to all kinds of websites that have VIN Decoders available. The best ones are backed by the Yamaha ATV manufacturer, however there are plenty of aftermarket Yamaha ATV VIN Decoder websites on the web. This topic will stay pinned and if you find any to add, please do it with a reply. 
      The following Yamaha ATV VIN Decoder websites are available where you can just enter your VIN number and it will shows you some of your ATV model details:
      KBB.com https://www.kbb.com/vehicle-history-report/ 
      CARFAX https://www.carfax.com
      autoDNA https://www.autodna.com
      VinAudit http://www.vinaudit.com/
      decodeTHIS https://www.decodethis.com
      VINCario https://vindecoder.eu/
      NICB Theft Check https://www.nicb.org/theft_and_fraud_awareness/vincheck 
       
  • Similar Tagged Content

    • Guest Fox300exchic
      By Guest Fox300exchic
      There are many ways to install grips and make them stick. The best one, short of having grip glue, is to use carb cleaner. First, clean your handlebars with carb cleaner and a rag, then spray the inside of the grips liberally. The carb spray acts as a lubricant first and then actually melts the grips enough so that it will bond to the clean handlebar. This works great for all but the most extreme conditions. If wet weather is involved, you really need to use grip glue, and in addition, you should follow that up with some safety wire.
      QUAD off-road magazine
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By dyyjrr9
      I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
    • By alexcross324
      Hi all, I try to find this manual in the threads but you have a lot of stock here
      Cannot find this particular manual.
      I found it for YFM200 but not sure if they are the same.
      Thanks if you could help me with that.
      Im new here so if I did something wrong, please tell me.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...