Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

blueflame62

Kawasaki 300/400 - Rear Differential Bearing

Recommended Posts

have anyone brought brought a rear diffferential beraing kit for kvf300a4or kvff400 does the kit include bearing for the pinion or just for axle and neeedle bearing inside rear diff look at some of the kit but doesnt say if included bearing for pinion sent request to find out but no response needed to know before ordering because the pinion bearing is really the only one i need but cant find where u can just buy the pinion bearing without buying pinion as a set.::confused:

Share this post


Link to post
Share on other sites


I d go to a local agricultural supplier that stocks all kinds of parts and tools for ag farms or a store that specialises in bearings. Just get the bearing out take it in and they will find one to replace it. Its also likely to be a lot cheaper to, that's where I go for all my stuff like ball-joints and bearings and the like.

Share this post


Link to post
Share on other sites

agreed with Earthmover. all you need is the bearing out to get measurements, and if you get it from an automotive store or bearing shop, your cost will drop to a third of the bike dealer's price ...

Share this post


Link to post
Share on other sites

i try three bearing company around here they couldnt help said was bearing make only for kawawaski pinion but i found a bearing repair kit and it does have the pinion bearing for $30 whick is cheap other kits cost about $60 but will keep the info u suggested in case need other bearing

Share this post


Link to post
Share on other sites

check your phone book for bearings if you can get a number off the old one it will help the bearings should be cheaper there .I was told it is safer to change them as a set as you should not have to take it apart again hope this helps

Share this post


Link to post
Share on other sites


already try they couldnt help but i just found a bearing kit for $30 that what one bearing and seal would cost so just replace all of them thanks

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Alois Specht
      Hi there , have a KAZUMA 500 JAGUAR the rear diff is permanently locked , how can I get it out of lock just about tried everything I think, ?? .  Thank you your help is appreciated.
       
    • By derick geisendorfer
      I found a black rubber hose hanging down from the front of my Sportsman 850.  I'm trying to see if it's the diff vent hose, or something else and if it's something else, what it's supposed to attach to...  
    • By Kevin Nicoll
      Anyone familiar with these models? Its a new to me quad, picked it up for basically nothing... Just time and materials now, this looks expensive. 




    • By caperwing
      The rear brakes on this are hydraulic and manual. The hydraulic part is all messed up so I disconnected it all and want to go just manual on the rear. I got it all put back together but doesn't seem to work to well, like not enough pressure. The manual says I should mark the casing before taking it apart which I didn't read until to late. Any ideas? I put new brake pads on.
    • By Jeff011366
      Hello,
        Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
       
        My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires....  Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
        It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
       
      Thank you in advance for sharing your knowledge.
      Jeff
  • Similar Tagged Content

    • By Alan Callison
      Hello boys and girls!:howdy:I need a little help if ya dont mind.I need to replace the rear axle bearings on my 400 but Im going at this blind having never done it before. Ive looked it up in the repair manual but it doesn't give any specific steps on how to do it. I've got the left rear brakes off already as I was replacing the shoes anyway. Can somebody give me a rundown on what Ive gotta do please?I know I need to pull the right wheel off just havent done that yet. Do I need to take anything apart in the final drive or elsewhere in order to yank the axle out for instance? Which side does the axle come out from,L or R? Any details I need to know will be greatly appreciated.Thanks ya'll!
    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By chuckcnm
      Hi, just picked up a MOTO 4 YFM255 and want to replace the rear brake pads. How do I get to the back. Guessing I need to remove the brake disk, question any easy way to do this?
      Thanks
    • By Kyboy
      Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate
    • By pizzaman_288
      How hard is it to change the outer seals on the rear differential mine are leaking fluid and I have no idea on how to change them out any help would be great thanks
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...