Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Dwight Williams
Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00. It's been sitting outside with no carburetor on it for about a year. Its rusty, missing some parts, wiring is all cut up and spliced etc. No seat, no racks but the plastic is all there minus the headlight housing. Anyway, who can pass up a $40.00 quad right? I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water. I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine. I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark. Did a quick compression test, 70 lbs. Wet test bumped it up to 90. Ok, so rings and cylinder washed out with water for a year, not too surprised. I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show it's got life. Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either. The compression is now around 60.
Anyway, my question is....is it worth it to try to get this thing going? I tore the top end down today and the cam and one of the rockers is pretty worn. I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well. Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again. Much less just to make it run and use as-is but I won't really like it until it's right. I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much. I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down? I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
I'll get some pictures today if anyone want to see them.
By Adrian Ciotinga
I recently picked up an ‘07 KFX 700. All was going well, rode it about 40 miles, when it started bogging at low speeds. If I kept the revs higher, I was just fine. Also, a persistent issue since I picked it up is the fairly difficult start (but it is abnormally cold right now and the quad is jetted for the dunes at summertime).
Regarding the complete lack of idle, I have to rev it a couple times to get it to idle after starting it, after which it’s 50/50 whether it remains idling. I don’t have low fuel, but all of this began after I rode it pretty hard and the radiator fan kicked in. Might be overheating, just wanted to hear your opinions.
By Nate Hanson
I am a new atv owner...I bought a used atv this summer (pretty sure it is a wolverine but reg card from last owner didnt actually say that so idk for sure). It ran great for most the summer and early fall but one day I tried starting it and it turned over a while without starting and then suddenly it quit turning over at all. No click or anything.
I charged battery and light turns on showing neutral and heatlight can go on.
A few other things that may be pertinent: The pull start is missing, I have a fluke multimeter but not many other advanced tools (or relevant experience), there is an extra aftermarket led light attached to front but it doesnt work either... never looked into why since I didnt need it.
I looked for a fuse box and didnt find one.
Please recommend some easier things to try first as I really want to avoid taking it in if I can (having one income and 4 kids can keep out extra cash, plus I want to learn). Pictures would be awesome if possible. Thanks!
Similar Tagged Content
Our 1988 Yamaha Terra Pro is finally seeing the finish line of becoming our new bush hogging tractor! I've had the terra pro for almost 2 years... we had great intentions, but after removing the fenders, fuel tank, and the carb, we let it sit up. Shame on us! However, the terra pro is cranking today. We cleaned the carb, figured out what goes where and where did that screw go! She smokes like there's no tomorrow, but that's okay! The only issue right now is getting all these lines hooked back up to the carb right! There is 5 lines to hook up to this thing!! And in our moment of drinking and removing parts, we cant remember how they go back on. I've found several diagrams online, but none showing the overall schematics of all the lines! If anyone has a service manual, or any way of helping us figure out what goes where I would really appreciate it!! I can attach pictures later if it'll help!
I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
Hi all, I try to find this manual in the threads but you have a lot of stock here
Cannot find this particular manual.
I found it for YFM200 but not sure if they are the same.
Thanks if you could help me with that.
Im new here so if I did something wrong, please tell me.
Hi all, my second post here
I got an old Yamaha 88 moto 4 and I have a problem with my overflow hose from the carb.
When I put the gas switch to ON a big amount of gas is leaking from the overflow...so I start using my quad with the gas switch to RESERVE wich is also leaking but less than in ON position.
I dont ride a lot..but in a week I empty my gas tank.
I never clean my carb because Im new to quad world and dont have the service manual...so I need you point of view.
Recently Browsing 0 members
No registered users viewing this page.