Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Brendan

2004 Warrior 350 clutch/shifting and reverse problem

Recommended Posts

When I am riding the atv it is easy to shift through gears and find neutral, but when the quad is sitting still and idling it is a lot harder to shift through gears; it takes a lot more force and it is difficult to get into neutral.

Also I can easily get the quad into reverse with it idling, but when i try to put it back it will only go halfway. I have to turn the atv off and then it comes out of reverse very easily.

I herd this might be an oil issue. Has this happened to anyone else? Any suggestions? Thanks

Share this post


Link to post
Share on other sites


you might try rocking the bike back and forth to make it easier when running, and there is an adjustment on the right side of the bike (sitting position) that is on the motor/transmission casing that looks like a nut and slotted screw. not sure which way to increase or decrease the tension.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Michael Rogers
      Anyone ever replaced the shifter shaft on one? Not sure on the year but assuming it is in the late 90's. Is it a huge task, splitting the case etc... thinking about buying it as my next project.
       
      Thanks
    • By ATVNetwork
      The 2020 ATV Motocross National Championship Series, an AMA National Championship, returned to competition in Georgia this past weekend with the Bulldog ATVMX National at Aonia Pass MX. This was the first round of racing for amateur riders, but the second round for the AMA Pro ATV riders, after their race at Daytona ATVSX kicked off the season.
      View the full article
    • By Erik Plug
      Hi all,
       
      Picked up my first Brute Force yesterday. What should have been an awesome afternoon of riding turn a bit into a deception. As I was unable to really take it out for a test drive at the shop, I decided to buy it and agreed that I would take the test drive at home. 
      When giving full throttle I noticed that the Brute was choking and lost all of its powers. Faulty fuel pump most likely. 
      Called the shop and the are coming to pick it up and repair it and bring it back. Good service. Nevertheless feels a bit sour in the mouth as I was told it was a 100% good. 
      Need to have some patience I now before I can really start riding. 
      Cheers,
      Erik
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
  • Similar Tagged Content

    • By Trenton
      Hello. I am a new member as of today. I had a quick question to ask. I recently was driving mt HONDA RANCHER 2004 GPSscape 400 and my display stopped working. I was driving the atv and all of a sudden the speedometer and the service lights went out. Also the lights stopped working. I am still able to shift gears, change from 2wd to 4wd, and can still select if I want EPS or Auto. I have checked my fuse box and have changed a few of them around. It did not change anything. I was wondering if anyone had any idea of what had happend. Thank you for your time- Trenton 
    • By LTZ-Zach
      So i was riding the other day and my quad randomly shut off. It started back up and ran completely fine for a little while and then it started idling terribly.
      I cleaned the carb and changed all the jets and everything except the float due to the rebuild kit not coming with one and it actually runs worse then it did before.
      It will run and idle decent now but when I give it gas it dies.
      Does anybody know what could be wrong?
      I also changed the spark plug and air filter along with the oil and oil filter.
       
    • By mallen14
      Looking for anybody who can point me towards a free service manual for 1998 Big Bear 350. I found the sticky thread but all the links, from 2012, no longer work. If anybody has one please let me know. Thanks
    • By kingjosk12
      A week ago I could not even get close to starting it. But now I adjusted the valves (exhaust valve was not closed). i got it running but would not run without choke. i adjusted the float because it was to low tried starting it up again and it would not even start. So i went back and looked at the valves and the valve was now open again so i adjusted it and it started right up and ran perfect without choke. So i put it all back together thinking it was ready to go. Started it up and let it run for a little bit. i turned it off and tried starting it again there was NOTHING. took it apart and there was 0 compression and the exhaust valve was open again. I am completely lost need help PLEASE!!!:aargh:
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...