Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By raybob
      replacing carb,, the bigger line on right side top of carb does it just vent to the air,, cant find where to hook it up to also I want to check the oil and gear oil I checked the oil in motor and the rear end my question is looks like allen plug on left side of motor if you are setting on the 4 wheller, ps it hs a oli leak any help would be great. Ray in kentucky
    • By raybob
      I have it all but can find where the vacuum line on the carb goes its a 2000 suzuki 500 quadmaster I know where the two vent lines go but not the bigger vacuum line goes it has vacuum on this line. need help. Ray
       
    • By Tahj
      Do I need to remove the balancer driven gear to remove the timing chain.
      If so, how?
      Thanks

    • By Tahj
      I am looking to see why my 2005 Grizzly  660 won't crank. I have set the valves but suspect a loose timing chain.
      When working to remove the valve cover I found a "cap tensioner case" - parts #25  - #299 on Babbitts site.
      The  cover seems to bridge the valve cover and the cylinder head. What the hell is it and what surprises will I  find if I remove it?
      Uncharted territory for me.
    • By David Cameron
      The small waterline insert for the hose that goes from the water pump cover to the thermostat housing has corroded off. I only need the insert on top and behind the thermostat housing that the hose goes over and can't find just the insert. It looks like it may be pressed in. I've have been told the entire motor housing needs to be replaced. The pic with the red line indicates where the hose and insert would be and the insert looks like the pic of the water pump  Any ideas would be really appreciated.
       
       



  • Similar Tagged Content

    • By JacobSlabach
      Hey I have a 97 bayou 300 2x4 (klf300b) that i bought for 1000 last June and sunk another 1000 into it already.  When i went to look at it, the seller had warmed it up before hand (he was riding it when I got there).  it ran good so i bought it and took it home that evening... next morning it wouldn't hardly start.  I discovered the carb was clogged, there was chunks of rust in the fuel valve, the choke lever was missing and other things.  I have since cleaned the carb and replaced the fuel valve and gas lines and cleaned out the gas tank and cap.  
      Enough background on it, the problem is this:  It floods if i push it past half throttle in 4th and 5th gear even going downhill and shifting correctly.  It also has to idle and warm up when you first start it which is really annoying now that its cold...  It also smokes blue smoke for about 15 seconds when started cold-  does not smoke at all once warm but the exhaust still smells like burnt metal.  A friend told me that it didn't have enough compression.  I also found out that the valves are a common cause for low compression on Kawasakis..  I have never adjusted valves before-  the most I've ever got into a engine was a head gasket on a riding mower so I'm new to this.  My goal is to get this bike running and starting cold like a top-  should i tear down and rebuild the top end?  What should i try first?  I tore the carb apart and rebuilt it and fiddled with the air screw and nothing changed.  I also ordered a compression test kit that should be coming in soon.

      Ive also considered just selling it for like $500 and taking the hit-  Id rather not sink too much more into this machine..  lol
    • By bradleyheathhays
      I'm going to check the valve clearance on my 2011 Grizz 700 for the first time and I'm also wanting to check the timing, but I'm not sure how to do it. What tool (light gun?) do I need for this job and how is it done?
    • By bogman
      Hi, does anyone know where to find the timing marks on the camshaft and how to orient them? I found the line on the crank and lined it up with the arrow on the case, but the only marks I can see on the cam are on the very end where the black plastic cap is. Are these the timing marks and if so how do you line them up?
    • By switch
      I have a really dumb question. My big bear came half apart and I am not sure how the timing chain guide is supposed to sit in there. I have the entire top end cleaned, bored, new piston, gaskets, etc. I do not see anywhere in any manual or thread where it shows how the chain guide is installed or held on place????? Also should it be the same height as the other side???
    • By alanminz
      Looking for timing info for a 2004 Outlander 400. Replaced chain and guides. looking for the diagrams but could not seem to find any yet.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...