Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

EatMyDirt

Where can I camp and ride in the tri-state area?

Recommended Posts

Anybody know of any locations in Indiana, Michigan or Ohio where I can take the family to go trail riding and have access to full RV hookup camping?

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By RedPillRight
      Any local family friendly areas.  Everyone I used to ride growing up in long gone or fenced off.
    • By Micah Gafford
      So the kids have a 110cc ATV I'm getting an old polaris xplorer up and running and I've been thinking about what kind of trail I should make. I've got some very wooded acreage and hills with creeks running through it. I'm planning on using a lot of the old logging road for the main trail but what do you normally want to come across when you're riding your ATV? Any suggestions on things I should build in? What would you make sure you had on a trail you built and what would you avoid doing?
    • By JacobSlabach
      i know this isnt an atv but same type of thing.  I have a riding mower im fixing and selling for my aunt and it has a dead battery.  i jumped it off my atv and when i turn the key nothing at all happens.  i tried jumping the relay still nothing.  this is with the seat down.  you wouldnt think this mower would have issues as its a top-of-the-line brand and almost brand new (aunt found it for a good price, still got tits on tires, just sat for a couple months in a mechanic shop
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
  • Similar Tagged Content

    • Guest Fox300exchic
      By Guest Fox300exchic
      Indicators that tell you to check your toe-in.
    • By pickytar
      I have a Chinese Hybird 250 or that's what I was told it was. I found 17 numbers on the frame. Will these numbers tell me exactly what it is that I have? (I know that its a 2006 from a plate on the front)
    • By buzzar56
      I am looking for a free repair manual for a 2003 Polaris sportsman 500 ho atv. all the posts on here lead me noplace
      thanks fred.
    • By txlora84
      I have a 110cc atv not sure of a brand its a Chinese model. I put on a new harness with cdi solenoid and all those. I have put a new starter on, and carburetor. I bypassed the start button cause it was just making the solenoid click. with the new button switch the atv will crank but not start. I tried to jump the solenoid and it did nothing. I am stumped. also I noticed gas leaking from the carburetor and when I took the filter off there was gas in it. I cleaned the carburetor and nothing was stuck or clogged. can someone help me out.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...