Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

brandon2013

2001 raptor 660 jetting

Recommended Posts

I was going to jet my raptor 660 I was planning on running without a aibox lid. What do you recommend on the jet sizes. Another website said 155l 160r 25 pilot jets. I also have a stock exhaust. Will I notice any power difference if i jet my quad and run without a airbox lid.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By MarkinAR
      Can you believe this thing blew a new head gasket after a few weekend rides? Granted, it was beat on in a mud hole every weekend, but this is a new head gasket on a 400 Kodiak. Bummer. 

    • By Venom
      Hi All,
      I did a total restoration on a 2003 Yamaha Raptor 80. Rebuilt the engine and tranny.. Started it up today and it runs great. Took it for a ride and the transmission worked perfectly. Adjusted the carb a little more and went for another ride. It ran awesome, pulled into the workshop shifted into neutral ( Neutral light came on) and shut off the bike. went to roll it and noticed she would not roll. Turned on the key and neutral light was on... After some troubleshooting I found that she is in first gear with the neutral light on and will not shift into neutral... It seems to up shift fine into 2nd and 3rd and then back down to 1st. I am hoping somebody can shed some light on what is happening... Thanks for any help...

    • By Venom
      Hi, All

      I started this project a while ago.. I have decided to make one thread I can continuously update..

      So , here we go. I got this Raptor 80 in really bad condition.. Rear end frozen, Engine toast, tires dry rotted, tons of rust..etc.. They admitted they beat on it very hard.

      Since they do not make these with a drive shaft anymore I decided to restore it from top to bottom..

      These are photos of when I got it home.

      Next up, the tear down..



      First, I needed to tear it down and determine if the rear end was still good... As we all know... That is where it would be cost prohibitive to restore if it is trashed..

      Got it completely stripped down and I lucked out... The rear Drum brake was caked solid inside with dried mud. That was causing the rear end to lock up. Took off the rear brakes and the rear end spun perfectly smooth.

      Once I got it all stripped apart I needed to take the finish off all the parts. I am going to be powder coating the frame and many parts.. Once the finish is off each part it will need to be sandblasted to white metal .. The guy I use for powder coating gives me a hefty discount if I bring the parts to him ready to go.

      You could just sand blast, but that would take a long time to get the finish off. First I used Aircraft Paint Remover.. That stuff is pretty toxic Goggles and Resperator are required. That quickly gets you down to the metal... Then you can sand blast to white metal pretty quickly...


      I had another thread I had started about a problem with the tear down... It has some great info .... here is the link... It is about removing the frame bushings. ....
       
      https://www.quadcrazy.com/atvforum/topic/14209-raptor-80-frame-bushings/?tab=comments#comment-104702
    • By Dwight Williams
      Ok, so I bought this scream of a deal the other day - a 94 King Quad 300 for $40.00.  It's been sitting outside with no carburetor on it for about a year.  Its rusty, missing some parts, wiring is all cut up and spliced etc.  No seat, no racks but the plastic is all there minus the headlight housing.  Anyway, who can pass up a $40.00 quad right?  I get it home and looked at the sight glass for oil level, it's about 1/2 oil and 1/2 water.  I drain it, refill it and turn the motor by hand (recoil starter is missing) and it turns over just fine.  I worked on the wiring for about an hour and got it to turn over with the electric starter and got enough of it sorted out to get a spark.  Did a quick compression test, 70 lbs.  Wet test bumped it up to 90.  Ok, so rings and cylinder washed out with water for a year, not too surprised.  I thought 'what the hell' and sprayed some starting fluid in it and it ran for about 2 seconds - enough to show  it's got life.  Since then the compression has gotten worse, I can't get enough pressure to activate the carb diaphragm, therefore no fuel pump either.  The compression is now around 60.
        Anyway, my question is....is it worth it to try to get this thing going?  I tore the top end down today and the cam and one of the rockers is pretty worn.  I figured a top end job would be about $100 or so, depending on the condition of the cylinder but I'll probably have to put a cam and rockers in it as well.  Doing some research on ebay I figure I'll have to spend about $500-$700 to make the whole machine right again.  Much less just to make it run and use as-is but I won't really like it until it's right.  I don't mind doing the work, I actually enjoy it but I'm concerned about what all that water did to the rest of the internals, I can't really test it all out until I can make it run.
      I know it's a basket case but I'm not into it much at all, even if I do the top end and find something else wrong I'm still not out much.  I'm leaning toward ordering the top end parts and going from there unless you can convince me otherwise - any way to check the rest of the internals without tearing it down?  I plan on flushing the oil cooler before I do another oil change, I've drained it twice now and it gets milky almost immediately just turning the starter - I suspect the oil cooler is polluted badly.
       
      I'll get some pictures today if anyone want to see them.
       
      thanks!
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
  • Similar Tagged Content

    • Guest Fox300exchic
      By Guest Fox300exchic
      If we had a dollar for every time the question “Which is really faster, the 700 or the 450?” shows up in our inbox, mailbox, or voicemail, we’d be putting this magazine together from a bungalow on a barely inhabited tropical isle named Quadhama.
      http://www.quadmagazine.com/quad/features/article/0,24942,1603755,00.html
    • By Bits52
      Thank you for your help, just got quad for my daughter n needs a little work [email protected]
      It's actually a 2002 , just found serial number. Thanks for any help that you can !
    • By switch
      I have a really dumb question. My big bear came half apart and I am not sure how the timing chain guide is supposed to sit in there. I have the entire top end cleaned, bored, new piston, gaskets, etc. I do not see anywhere in any manual or thread where it shows how the chain guide is installed or held on place????? Also should it be the same height as the other side???
    • By biggreen2010
      ok it will start up an run but quits a lot till it gets warm, but has a bad miss an wont idle, I have a brand new Honda carb on it, good gas flow, new plug, but when I let the throttle go below a quarter, it backfires through carb an tail pipe:confused: so it has never had any electrical work or mechanical work done...it just started all the sudden, I'm think it may have ignition coil breaking down, or cdi box going bad...anyone had this trouble before? let me know what you did to fix it. thanks:skeptic:
    • By higdon87
      Need some help i have a 2001 400ex that smokes on start up and smokes even more when you give it throttle. I just noticed that it leaks oil at the header and motor connect. I just got it from a guy that said he rebuilt the top half and he told me that the valves needed to be adjusted. But what will make it leak? Thanks in advance
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...