Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

google7

2006 Kawasaki Brute 750 - Spark Issue

Recommended Posts

ok so I got this 06 Brute force 750 in the shop came in no start put a new battery in turn key on and 30A fuse pops replace it try again another 30A fuse gone check wiring harness found 4 prong plug brown and black/yellow wires rubbed through and shorting out fixed that issue replace fuse and try again..... 30A fuse pops again play around for a while and found the CDI has shorted out on the 4 prong plug in cdi side . there was a dynatek cdi box in gave customer choice stock cdi for 300 ish or dynatek for 150 ish brought in new dynatek plug in and starts nice iddles for 5 to 10 seconds and dies ... crank it for a bit nothing ... turn key off then turn on and start .. starts up idles for same amount of time then stalls check out and no spark

why would it start and stall after 5 seconds and have no spark

I'm confused

please help

Share this post


Link to post
Share on other sites


05 and 06 have problem with wiring harness. you can replace the harness( what i have done) or you can fix the wires Buss connector. make sure you have fact ignition switch.

Share this post


Link to post
Share on other sites

Sound like you are having more fun than me, I'm currently having no spark and my ride will not start. I've narrowed it down to the crankshaft sensor. This is not your problem because yours will run for a few seconds. Good luck and keep us posted.

Share this post


Link to post
Share on other sites
ok so I got this 06 Brute force 750 in the shop came in no start put a new battery in turn key on and 30A fuse pops replace it try again another 30A fuse gone check wiring harness found 4 prong plug brown and black/yellow wires rubbed through and shorting out fixed that issue replace fuse and try again..... 30A fuse pops again play around for a while and found the CDI has shorted out on the 4 prong plug in cdi side . there was a dynatek cdi box in gave customer choice stock cdi for 300 ish or dynatek for 150 ish brought in new dynatek plug in and starts nice iddles for 5 to 10 seconds and dies ... crank it for a bit nothing ... turn key off then turn on and start .. starts up idles for same amount of time then stalls check out and no spark

why would it start and stall after 5 seconds and have no spark

I'm confused

please help

Ignition switch itself could be faulty, ign switch is a good place for power and ground to meet (blown fuse) wich is killing the power to the cdi, or the cdi is detecting <> 5volts dc and shutting down. Ck your roll over sensor as well.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Hondasher
      I have a 2004 Polaris Trail Boss 330 and I want to eventually fix it up if possible, but the thing is the transmission or Gearbox that allows you to shift into forward and reverse and such isn't connect to the engine at all, it isn't even bolted into the frame. Anyways the Secondary Driven clutch is missing. The ignition was busted so I switched it out and tried to hook up power to it and the lights wouldn't light up and it wouldn't try to let me start it with the electric starter. 
       
      So I bridged the connectors on the starter solenoid and it cranks the motor. I was wondering if anyone knew why the dash lights don't work or any of the buttons. I did find a cable disconnected I have a picture of maybe someone can tell me what it's supposed to be connected to. It has 3 wires going to the connect Green Purple Red. I'll enclose a picture of it and where it is connected on the wiring harness. 
       


    • By Johnnyhorsepower
      I finally found an awsome app for your phone that shows you on a map all the trails near your location. You can read or add reviews, look at picts...etc
      Its called: atv escape

      John
    • By Andrew Baker
      I need help with wiring on a 1998 (I think, 10th digit of the VIN was W) Bayou. I'm not getting spark, I'm pretty sure it is due to grounds being off because the harness is pretty hacked as far as the electric start and charging system goes. I'm needing a good wiring schematic. I found one online and there are a few things that don't add up on it so I'm skeptical that it is really for my year and model. Any help would be appreciated. Thanks. 
       
    • By David Miller
      Does anyone know how to access the check engine codes on a 2018 450 sportsman. Just changed battery and spark plug . It runs fine but the light is on and I need this to plow snow and need it reliable. Any ideas . Thanks
    • By Joseph Miller
      Hi guys im new here and ive been doing alot of research on my polaris predator i was wondering if anyone on here has wired a different cdi up on there quad? Not a direct replacement that would simply just plug in. I know my white an w/red wires go to my pulsar my green an blue go to my reverse coil but im unsure which is + and which is ground also brown/w is a ground correct? What about purple? Black goes to my kill switch and red is my 12v supply........then ive got yelloww/red , yellow / yellow that goes to my rectifier..........any input on this subject is greatly appreciated thank you all
  • Similar Tagged Content

    • By crazynordlander
      Hi All,
      I live in Minnesota and bought a 2016 CFORCE 500 HO. I am in hope to see if there is anyone in the US that is experiencing this sudden drop off in RPM below 4000 RPM. I have uploaded some videos of my issue on YouTube. I will list three of the four I posted. The fourth can be found on my channel but it is a comparison between my Polaris 570 and my CFORCE 500.
      I quit on my first dealer because we just did not mix well together. I brought it to another CFMOTO dealer that just became a CFMOTO dealer in January 2016. They are in a large ranch and agriculture area in a neighboring state that is pretty close to where I live. They have close to every brand available. They are a much larger dealer than the first one I bought the unit from.
      I brought the unit three weeks ago to them and they have worked on it a good solid week and have given up on it. I have read reports from owners in Canada that the dealers there were aware of the issue and have had success in fixing the herky jerky drivability issue.
      I am picking it up tomorrow and bringing it back home. It has been to the trails of the Black Hills this year and was new in late April. 300 miles on it. It has never changed. Very hard to ride on the trails or when I herd livestock.
      Here are the links to my videos.



      I can't accept that this is normal operation. Does anyone from CFMOTO China scan these posts?
      I need help that CFMOTO USA has not provided.
      Thanks
      Kevin
    • By Kyboy
      Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate
    • By pickytar
      I have a Chinese Hybird 250 or that's what I was told it was. I found 17 numbers on the frame. Will these numbers tell me exactly what it is that I have? (I know that its a 2006 from a plate on the front)
    • By oleskool
      have an 05 750, and she bangs out when you give it gas.
      Idles fine. Also the belt light is flashing, even after a new belt was put on.
      Any ideas?
    • By kiwisteve
      Hi Folks
      MY Ltf 400 has power and electric start turns motor over, but wont start...
      seems no spark
      im told stalled in paddock and wont start again
      any suggestions please
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...