Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

jesseo

2002 Honda 400ex - Wont Stay Running

Recommended Posts

ok I have a 400ex that will not stay running. it runs for about 5 to 10 mins then starts to die out once it does die it wont start back up til it cools for a few mins when it dies I try to start it, it turns over fine but wont start but if I just barely I mean barely touch the gas it will turn over like the battery is about dead it looks to be getting spark so I don't think that's it I have put new wiesco piston rings 416 cylinder stage 2 hot cam stage 2 dyno jet kit uni filter in it since I got it not sure if it did it before all these parts cause when I got it, it had a blown head gasket. if anyone could help it would be greatly appreciated :aargh:

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By fox300exchic
      Let's hear all there is to know about you ladies! Where your from and where you've lived. Kids or no kids. What you do for a living. Why you ride and how you got started.
    • By MarkinAR
      Working on my oldest son's buddy's 2000 Big Bear.  He was having some power loss at WOT so i thought it worth while to clean the carb and put at kit in it...or at least clean the OEM jets and use the new orings that come in the kit.  It starts and idles like a champ, but dies and wants to backfire with any throttle at all.  I assume lean because it will run decent with the choke on. Air screw adjusted fine, nice crisp idle.  This one has fuel/air screw, low speed jet, mid jet, and main jet.  I was assuming just trash in the low speed circuit so pulled it and cleaned again, still does the same. 
      Two questions I guess:
      1. Does it sound most likely trash in the off idle circuit?  This one has a few more passages and jets than I'm used to...and a darn diaphragm.
      2. It now really wants to leak at the bowl drain screw.  It doesn't seem to tighten enough to completely stop the flow.  Seat looks good, screw was dirty but cleaned up fine with a touch of 2000 grit paper.  First for me.  Any idea here?
    • By Shook
      Hi I have a 2000 big bear 400 and i just put a new carburetor on it and it idles fine but when you try to accelerate it sounds like it is going to die, so when it sounds like it is going to die I will give it more throttle then it will go just fine.
    • By stinky
      I have an Outlaw 110 that will struggle to turn the engine over. Jump starting doesn't help other than the battery will drain LONG before the bike eventually starts, so is required. If you keep messing with it long enough it will eventually magically begin to crank fine and sometimes finally start. Once we finally get the bike to start and warm it up thoroughly, it will turn over and start just fine the rest of the day like nothing ever happened... next day it won't turn over again.  Internet research has found lots of people saying they replaced starters, starter clutch, wiring, etc. but with only about 50/50 success rate for their particular problems... and I never found anybody describing a problem like mine, so I'm looking for advice/experience. Would rather not just start blindly throwing parts at it. Does anybody have any thoughts/ideas?
    • By Lank Firdmont
      I have seen other posts and I'm not ableto download resources.
      I was gifted a Yamaha TerraPro and can find 0 online for help getting this running.
  • Similar Tagged Content

    • By Wali
      I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
      when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out 
       
      Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
      When i try to pull start (push start/roll start) it made a not normal sound  and wouldnt stay running.
      If my bottom end is blow why would it still turn over fine,
      Are my valves siezed or not working properly 
      or is my timing off causeing valves to not open in correct order with fire 
      PLEASE HELP all help is appreciated 
    • By Coral Breding
      I loosened the allen bolts on the carrier and when I went to put my driver in the alot to pull back and tighten the chain, I noticed the holes were facing the front of the bike. I tried to slide a driver in and tighten the chain but the thing would not budge. I nearly ripped the tip off the driver in the slot. Any suggestions? 


    • By afa913
      Am i better off to just replace the bearings or buy the whole carrier?
    • By afa913
      Anyone know a place i can find a used stock pipe for a 400ex?  I would love to find a take off
    • By Jordan Alexander
      The title is for attention. I’m prepping my cylinder head off of an unknown year 400ex to install on my quad. And I’m examining it and there’s literally a Jewish start( Star of David) protruding from the metal on the camshaft side of the head. It’s not imprinted or etched/ engraved. It’s coming out of the metal. DOES ANYONE HAVE INFORMATION ON WHY ITS THERE??? I’ve attached a picture 

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...