Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Mattadki

1996 Yamaha Wolverine - Carburetor

Recommended Posts

I was just given a 1996 wolverine for Christmas from my father in law, needs a new carb. The cheapest that I can find a new one is $500, looks like it's an oddball carb. Is it possible to use a warrior carb which is a lot less expensive and more available? I found an aftermarket wolverine carb for like $170, anyone had any luck with these?

Thanks!

Share this post


Link to post
Share on other sites


My father in law took it to a dealer to have it rebuilt but they told him that they couldn't get the main jet out of the nozzle. So someone clamped onto the stem that the nozzle goes into with vise grips attempting to hold the nozzle still I guess, now the whole stem will turn in the base of the carb, looks like it's screwed to me. Thanks for your reply!

Share this post


Link to post
Share on other sites


No, that's the main jet nozzle, I need the plastic housing that that nozzle presses into. It's not available separately, only sold as part of carb assy

Share this post


Link to post
Share on other sites

I have a 96 kodiak parts bike. Not sure of condition of the carb i can ck for yo. Also i have had no problems with 9 carbs i have bought from ebay. Look up "caltric" :seller

Share this post


Link to post
Share on other sites

I just went ahead and ordered an aftermarket on ebay from zoom zoom parts for $170, caltric didn't have one - it's good to know that you've had good luck with them, thanks!

Share this post


Link to post
Share on other sites

ON the Hondas and Yamaha most of the time i had to drill out the 14mm nut that hold the enrichner cable to the carb. bore out the inside so cable would go down in there far enough to give plunger enough free length to close. Dont assume jets are correct size, dont expect them to have numbers on them. I try and order fact name brand jets and put those in place of the ones that come in it.. You will get your best results that way. If you happen to need any used part for your Kodiak i may have it. Fresh part out!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By John Ford
      i ordered a keihin carb for my 07 trx 90 and it fits nicely but the new cable they sent is way too long and i can't make it work.  the old honda cable cap [that fits on top of the carb] is too small to fit.  the keihin cap is approx 3/4 or 19mm.  honda cap is more like 1/2 in.  the keihin has a rubber boot on the cap where the throttle cable goes through . i don't know how to find the right length [most cites don't give the length].  i'm not sure how cables fit into that boot  and do i need to add the length of the boot to the cable?  the old honda cable is 28 inches total, but the cable movement is only approx 2'' which would not be enough to reach the actuator block on the keihin.  looking to find a throttle cable compatible with the keihin.  any help, please.
       
       
    • By JacobSlabach
      got 7 atvs off CL recently for a good price.  one of which is a yamaha warrior.  anyone know where the vin is printed on this bike?  Haha good place to start as I do not know year or size yet.  The former owner says needs exhaust ans and clutch work.  he said it ran fine until the clutch cable broke and then I couldn't get the new cable adjusted right and it would grind gears.  things I see:  clutch cable locked up again, no brakes, carb leaking (green with algae around the bowl and has gelled gas stalagtights on it), aftermarket exhaust melted the airbox so I need something different and a new air box.  I would like the use the current exhaust if I can but I have a feeling its a redneck fix as it looks like there is an ace bandage holding it to the exhaust pipe (its an aftermarket slip-on exhaust), so I'm not sure about that- lets get the bike running first.  also, battery (looks brand new, what a shame) is dead, 0 volts.  Otherwise, bike looks to have not been wrecked, and plastics are ok (it sat outside under a 'tarp' for 3+ years since it was run last).  any tips and advise on where to start first would be awesome as this is my first clutched bike (manual).
      the clutch is my main concern- I've never rode a clutched bike so I dont even know what its supposed to feel like.  lol I'm spoiled on my automatic polaris 
    • By Squirrel
      So I bought a Bayou 220 as me 'Black Friday' score, and was informed it has carb issues.. 
      A little history from the previous owner: they suspected the carb was bad as it was 'running like crap' so they did a rebuid kit on it. Didn't fix issue so they took it to a shop where the tech installed an aftermarket(?) carb, but had to modify the throttle cable to get it to work. Quad ran great at 1/4 throttle, but anything above that and the throttle would stick and the machine would run like garbage again.
      What I know and think: I hear carb issues are common and fairly easy to fix. Also, I think they used the 'universal' rebuild kit that claims '88-'11, but the jets and such were different from '00-'03 (gaskets, etc. appear to be the same) so their original attempt was a good idea, just not good enough.
      They did give me the original carburetor with the 4-wheeler, but it has the wrong internals. I'm thinking if I can get the right jets, springs, etc for the rebuild, I should be able to get this thing running right. Of course, I still need to charge the battery back up, change all the fluids, replace fuel lines, plug and wire.. ya know, the basics for a machine that's been sitting for roughly 9 months. lol
    • By goldeneagle
      I have a 2000 warrior thats seems to run fine. But I am having a problem with the gas boiling in the tank. Does anyone else have this problem or can anyone give me suggestions on how to fix this issue? Thanks Bill.
    • By Admin
      1996-2001 Suzuki LT80 Service Manual
      View File 1996-2001 Suzuki LT80 Service Manual
      Submitter Admin Submitted 06/29/2019 Category Suzuki ATV  
  • Similar Tagged Content

    • By M0BJT
      Hi Everyone
      This is my first post and I was wondering if there is anyone who can help me solve a problem I have with my Yamaha Kodiak 400 4x4 Fitted with a Mikuni Carburetor . The year of the quad is around 1998, the reason I am not sure of the date is, there wasn't any paperwork and no details on the frame either.
      The quad had a bad leak from the carb overflow which indicated that the float needle valve was blocked or passing so I replaced this and put everything back together. The quad ran really well until I took it onto some rough ground to have a ride around, a few hours later the engine started to run really rough as if the engine was flooding. I have removed the carb again and cleaned the needle valve out and the whole of the carb just in case there where any dirt behind it. Engine now runs fine again but fuel has started to run out the carb overflow again.
      I have tried everything to try and stop the fuel leaking out the overflow but its still happening. My last thoughts where to adjust the float level and its still happening.
      Has anyone got any thoughts on the problem or could suggest whats causing the fuel leaking out the overflow.
      Thanks for reading
      Kevin
    • By Wonderwoman
      Hello, well back to where I was last year with this carb. Took my 250 to the mountains for the first time this year and blue smoke, too much gas again. I can't believe that this carb gives me this much trouble. Seems like the choke is stuck but the cable moves freely. Anyone else ever experience this issue? Do you think a new choke cable would maybe resolve this?http://www.quadcrazy.com/atvforum/images/smilies/arghh.gif
      OK it was the choke. Put on all new cable and plunger and she is running 100% again. So now the question is, is the carb getting worn out where the plunger needle goes in the small hole and when I use the choke the needle end doesn't get lined back up with the hole?? We'll see how it runs and now that I know what the issue is I can always pull the choke plunger out and reinstall if I start having this issue again.
    • By davidwestfall
      hey I'm dave westfall I'm new I just became an official member of this site a few minutes ago. Ive been crazy about quads and bikes since I was about 3 and ive always done my home work on them figuratively speaking. I would say for comparison to the common man that I am pretty knowledgeable about them. its been my passion about most of my life. I love talking about quads and bikes so if anyone out there would like to talk with me about mechanical subjects or about person experiences while riding or just shoot the breeze please feel free to chat with me. I'm looking forward to it.
    • By ej200421
      i was wondering if i could get some help. i been trying to locate where the fuel and air adjustment screws are located on my 95 kodiak 400. i think i found the fuel screw.. i know where the throttle adjuster is but i cant find the air screw. or is there an air adjustment on these carbs?
    • By ut1w7b
      I have a 94 sportsman 400. It sat for several years before i got it. I have cleaned the carb it will start and run for about 5 min then it will flood. I have torn it down and cant see anything wrong. has anyone else ran into this problem any hel would be great.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...